Carburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb
Hover over the image to zoom in
Share this:

Proform Carburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb

Part No. 67101C Warranty Details  

Fit of this part varies by vehicle & equipment specs Type of Fit



Product Features:
  • Direct Replacement Components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance carburetor main body (no re-built components). Easy swap-in, swap-out installation utilizing existing metering blocks, fuel bowls, and baseplate. Involves only 14 screws. Has adjustable screw-in air bleeds, high-performance down-leg boosters. Get maximum air flow with no air horn, choke tower, or choke control. Comes with instructions, all necessary non-stick replacement gaskets, and high-performance jet kit. PROFORM is a registered trademark of Specialty Auto Parts USA, Inc. Holley® and Double Pumper® are registered trademarks of Holley® Performance Products, Inc. This product is manufactured by Specialty Auto Parts USA, Inc. and it is not made by or endorsed by any other carburetor manufacturer.Technical Note: Main body does not retain vacuum advance port in original metering block.
Back To Top

REVIEW SNAPSHOT®

by PowerReviews
ProformCarburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb
 
5.0

(based on 1 review)

Ratings Distribution

  • 5 Stars

     

    (1)

  • 4 Stars

     

    (0)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

Reviewed by 1 customer

Displaying review 1

Back to top

(1 of 1 customers found this review helpful)

 
5.0

Excellent HP to Cost Ratio

By 

from Jersey

About Me Auto Enthusiast

Pros

  • Easy To Install
  • Increases Power

Cons

    Best Uses

    • Performance Driving
    • Racing

    Comments about Proform Carburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb:

    It took less than 30 minutes to change out the main body in my holley 750. I'm using the carb on a fairly built 396 that's good for a 12.85 quarter mile in a 65 vette. The difference was impressive. No noticeable degradation down low, very noticeable improvement on the top end. I haven't taken the car back to the strip, but I'd say that the Proform main body is a very cost effective way to pick up horsepower, assuming that your engine could benefit from more air-fuel. It's a whole lot cheaper than a Holley HP.

    Comment on this reviewHelp Icon

    Do you have questions about this product?

     

    Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

    3 Questions | 3 Answers
    Displaying questions 1-3
    • Q:

      Do you have this part for mechanical secondaries
      Asked on 9/23/2015 by keith from United States

      1 answer

      • CUSTOMER CARE

        A:

        Sorry, Keith. This ProForm Carburetor Main Body for Holley 750 Cfm, (Part No. 67101C) is not available for mechanical secondaries.

        Answered on 9/24/2015 by Solomon
    • Q:

      does the holley 750 proform work with vacuum disk brakes? And Edelbrock intake?
      Asked on 4/29/2015 by fred from United States

      1 answer

      • CUSTOMER CARE

        A:

        I'm happy to help, Fred! This ProForm Carburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb (Part No. 67101C) is engineered to fit a Holley 4160 series 750 CFM carburetor (Part No. 3310). Typically the vacuum for your brake booster is connected to the intake manifold, so the main body replacement should not affect your booster. Installation instructions for the main body are available here: https://www.proformparts.com/common/instructions/67100C_67101C_Install.jpg.

        Instructions for a Holley 3310 carburetor are available here: http://documents.holley.com/199r9934-3rev4.pdf.

        Without knowing the intake manifold you've chosen, it's difficult to predict if the carburetor will work well with it. If you could please provide the part number of the intake manifold you have in mind, we can provide more details. Edelbrock typically provides carburetor recommendations with their intake manifolds. We can also provide additional product recommendations with if we have an idea of the intended purpose of the vehicle. It looks as though you will require an Edelbrock Performer RPM Series intake manifold. These are best utilized for 1500-6500 RPM engine speeds and may not work well for a daily driver.

        Answered on 4/29/2015 by Heath, ASE Parts Specialist from AAP
    • Q:

      is this proform 67101c body made of aluminum?
      Asked on 8/21/2013 by Tom from denver

      1 answer

      • CUSTOMER CARE

        A:

        Yes, the main body material of this ProForm Carburetor Main Body for Holley 750 Cfm, Vacuum Secondary Carb -part# 67101C is made of aluminum. For any further assistance, please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

        Answered on 8/21/2013 by Vincent from AAP
    Displaying questions 1-3

    Do you have a question about this product? 

    Check out the specials in our monthly flyer.
     
     
    Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.