QwikData Wheel/Shaft Speed Sensor Kit
Hover over the image to zoom in
Share this:

Edelbrock QwikData Wheel/Shaft Speed Sensor Kit

Part No. 91115 Warranty Details  

Fit of this part varies by vehicle & equipment specs Type of Fit

Product Features:
  • Magnetic Sensor With 2 Rare Earth Magnets
Back To Top

Do you have questions about this product?

 

Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

5 Questions | 5 Answers
Displaying questions 1-5
  • Q:

    How do you replace the left wheel speed sensor on a 2006 Trailblaser? Is this also the ABS sensor?
    Asked on 12/7/2012 by Tom from irondequoit, NY

    1 answer

    • CUSTOMER CARE

      A:

      With reference to this Edelbrock QwikData Wheel/Shaft Speed Sensor Kit - part# 91115, wheel speed sensors are located on the wheel bearing assemblies. There should be one bolt holding the sensor in. Make sure the area near and around the sensor is clean, if you knock any dirt dust into the open sensor shaft it will go directly into your wheel bearing, causing more issues. Pull sensor out firmly and straight. Do no pry sensor out with anything, as you will bust sensor off in shaft. Do not attempt to remove the stainless shim, as it is permanently fixed to the assembly. Clean the area if needed, then insert the new sensor carefully. Again, remember to not get dirt inside of the wheel bearing assembly, or you will be replacing the entire assembly soon enough. Yes, this is also the ABS sensor. For any further assistance, please visit your nearest Advance Auto store or call us directly at 1-877-ADVANCE (238-2623) and one of our representatives there would be more than happy to assist you.

      Answered on 12/7/2012 by Vincent from AAP
  • Q:

    how do you install wheel speed sensor on a 1999 Pontiac Montana extended length?
    Asked on 11/14/2012 by Mike from Knoxville, Tn

    1 answer

    • CUSTOMER CARE

      A:

      Instructions to replace speed sensor on Pontiac Montana: 1. Use a lug wrench to loosen the lug nuts on the passenger side tire. Do not remove them yet. Raise the front of the van with a jack and secure it on a set of jack stands. Remove the lug nuts and the passenger side tire on the front of the van. 2. Locate the vehicle speed sensor. You will find the Pontiac Montana's vehicle speed sensor attached to the rear of the transmission, just above the transaxle, where both axle shafts connect from the wheel hubs. Pull the electrical connection free from the sensor. 3. Remove the mounting bolt from the sensor body using a socket and ratchet. Support the sensor body when you remove the bolt so it does not fall. 4. Pull the vehicle speed sensor free from the mounting case. Make sure the o-ring comes off with the sensor. If not, pull the o-ring out of the mounting case. 5. Attach a new o-ring to the new speed sensor. The o-ring should be included with the new sensor when you purchase it. 6. Insert the vehicle speed sensor into the mounting case and secure it with the retaining bolt using a socket and ratchet. Use a torque wrench to torque the retaining bolt to 106 inch-pounds, as recommended by Pontiac. 7. Mount the right front tire and replace the lug nuts until they are hand-tight. Raise the front of the van with a jack and remove the jack stands. Lower the van to the ground and tighten the lug nuts securely. For further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and one of our representatives would be more than happy to assist you.

      Answered on 11/14/2012 by Steve from AAP
  • Q:

    How do you replace the wheel speed sensor on a 2005 Saturn Ion Redline 2.0?
    Asked on 10/26/2012 by JVan

    1 answer

    • CUSTOMER CARE

      A:

      While replacing the Wheel speed sensor/hub assembly on your 2005 Saturn Ion Redline 2.0 follow these steps: Remove the 3 wheel bearing/hub assembly mounting bolts. Remove the wheel bearing/hub assembly and spacer from the steering knuckle and wheel drive shaft. Install the wheel bearing/hub assembly and spacer to the steering knuckle and wheel drive shaft. Position the spacer and install the wheel bearing/hub assembly mounting bolts. Tighten the bolts evenly to draw the bearing assembly to the steering knuckle, and then tighten the bolts to specifications. Tighten the bolts to 115 N.m (85 lb ft). Install the wheel speed sensor jumper connector to the harness retaining bracket on the strut. Connect the electrical connector to the wheel speed sensor jumper. Install the brake rotor and install the brake caliper and bracket as an assembly. Install the wheel drive shaft nut. Finally install the tire and wheel assembly. For any further assistance please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto store and one of our representatives will gladly assist you with any questions or concerns you may have.

      Answered on 10/29/2012 by John the Car-Doc from AAP
  • Q:

    how do you replace a rear wheel speed sensor on a 2006 jeep grand cherokee laredo 2wd 3.7?
    Asked on 9/23/2012 by lee the learner. from tampa,fl.

    1 answer

    • CUSTOMER CARE

      A:

      This part Edelbrock QwikData Wheel/Shaft Speed Sensor Kit, Part No. 91115 is universal and not a direct fit for your vehicle 2006 Jeep Grand Cherokee Laredo 2WD 3.7L. This is a one size fits most, slight modification may be required. For help with your installation project, I would recommend purchasing a repair manual specifically for your vehicle. This should be able to assist you on how to repair or replace specific parts.
      For any further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and our representatives would be more than happy to assist you.

      Answered on 9/24/2012 by Aaron from AAP
  • Q:

    How do you replace the rear wheel speed sensor on a 2006 ford explorer?
    Asked on 5/25/2012 by Anonymous

    1 answer

    • CUSTOMER CARE

      A:

      The required information on replacing wheel speed sensor on 2006 ford explorer has been sent to the mail address.

      Answered on 5/26/2012 by Dennis from AAP
Displaying questions 1-5

Do you have a question about this product? 

Check out the specials in our monthly flyer.
 
 
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.