Suspension Ball Joint
Hover over the image to zoom in
Suspension Ball Joint Suspension Ball Joint Suspension Ball Joint
Share this:

Driveworks Suspension Ball Joint

Part No. DW-K6293 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Driveworks chassis parts help to eliminate front-end vibration, shimmy and unsafe handling. Driveworks chassis parts meet OE specifications, help ensure improved steering response and reduce tire wear.

Product Features:
  • Forged housing provides exceptional strength and durability
  • Oxidation film on the surface of the metal protects against corrosion
  • Phosphated ball stud provides a smooth, durable and wear-resistant surface to extend service life
  • Premium Polychloroprene rubber boots are fitted with grease relief valves to prevent contamination
Back To Top
Greasable:Yes
Material:45#Steel:51=H 40Cr:40=H Others:9=H
Outside Diameter:58.54 mm
Stem Thread Diameter:M16*1.5
Stem With Cotter Pin Hole:Yes
Arm and Joint:No
Ball Joint Only:Yes
Dust Seal:Yes

REVIEW SNAPSHOT®

by PowerReviews
DriveworksSuspension Ball Joint
 
2.4

(based on 5 reviews)

Ratings Distribution

  • 5 Stars

     

    (1)

  • 4 Stars

     

    (1)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (3)

40%

of respondents would recommend this to a friend.

Pros

No Pros

Cons

No Cons

Best Uses

No Best Uses
    • Reviewer Profile:
    • Auto enthusiast (3)
    • Was this a gift?:
    • No (5)

Reviewed by 5 customers

Displaying reviews 1-5

Back to top

 
1.0

update on not bad !!!!!!!!

By 

from nc

About Me Auto Enthusiast

See all my reviews

3 or more reviews submitted

Pros

    Cons

    • Junk

    Best Uses

    • Na

    Comments about Driveworks Suspension Ball Joint:

    After my 5 star review because the fitment was perfect and all felt good once installed.( and it was torqued and done properly. i GOT THE TRUCK ON THE LIFT FOR THE ALIGNMENT AND ONE SIDE WAS STRONG AND THE OTHER SIDE BAD :(:(:(. So disappointing . will never buy again or recommend them. Just get a moog or dealer parts. This is the first time i have used anything other than ac delco just cause local store was out of stock and i needed my truck before they could get the part there. NEVER AGAIN. I drove my truck 1/2 mile to shop and the bad one moved worse than the balljoing i replaced. i also just had new 450 set of tire put on my dually . think god it went then rather than 400 miles away with a trailer load.

    • Was this a gift?:
    • No

    Comment on this reviewHelp Icon

    (1 of 1 customers found this review helpful)

     
    5.0

    Not Bad

    By 

    from nc

    About Me Auto Enthusiast

    See all my reviews

    3 or more reviews submitted

    Pros

    • Durable
    • Easy To Use
    • High-Performance
    • Lightweight
    • Versatile

    Cons

      Best Uses

      • Trucks

      Comments about Driveworks Suspension Ball Joint:

      Installed perfectly and works as it should. My only issue is they were not match styles for each side. But to work as intended.

      • Was this a gift?:
      • No

      Comment on this reviewHelp Icon

       
      4.0

      worked fine

      By 

      from IL

      About Me Auto Enthusiast

      Verified Buyer

      Comments about Driveworks Suspension Ball Joint:

      Fit good

      • Was this a gift?:
      • No

      Comment on this reviewHelp Icon

      (2 of 2 customers found this review helpful)

       
      1.0

      never again

      Profile Image

      By 

      from pittston pa.

      Verified Reviewer

      Pros

      • None

      Cons

      • Incompatible

      Best Uses

      • None

      Comments about Driveworks Suspension Ball Joint:

      does not fit a 1989 c2500 the ball joint is .080 smaller than the lower control arm had to be welded in as it was late at night and had to get truck on the road.

      • Car & Truck:
      • Mechanic
      • Was this a gift?:
      • No

      Comment on this reviewHelp Icon

      (3 of 4 customers found this review helpful)

       
      1.0

      I would not buy this product again

      By 

      from pittston pa

      Helpful Reviewer

      Pros

        Cons

        • Incompatible

        Best Uses

          Comments about Driveworks Suspension Ball Joint:

          does not fit the control arm. had to weld it in to get the truck back on the road. if wasn't my own vehicle and late at night would not have used it. very unsatisfied with this product.

          • Car & Truck:
          • Mechanic
          • Was this a gift?:
          • No

          Comment on this reviewHelp Icon

          Displaying reviews 1-5

          Back to top

          Do you have questions about this product?

           

          Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

          1 Question | 1 Answer
          Displaying question 1
          • Q:

            Will this work on my 88 Chevy c-1500...I've heard this is a little to small and had to be welded in place?
            Asked on 9/25/2013 by Clay from Burlington, NC

            1 answer

            • CUSTOMER CARE

              A:

              This Driveworks Suspension Ball Joint - Part No. DW-K6293 is an exact fit for your 1988 Chevrolet C1500. For any further assistance please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

              Answered on 9/25/2013 by Morgan from AAP
          Displaying question 1

          Do you have a question about this product? 

          Check out the specials in our monthly flyer.
           
           
          Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.