Hub & Bearing Assembly
Hover over the image to zoom in
Share this:
Receive a Free MOOG hat by mail with purchase of any MOOG wheel bearing hub assembly. See Rebates page for details.

Driveworks Hub & Bearing Assembly

Part No. NT513198 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Driveworks Hub & Bearing assemblies are designed to meet or exceed original equipment (OE) standards in form, fit and function. These Hub & Bearing assemblies are designed to support the vehicle's weight and reduce resistance so that your wheels maintain contact with the road under any condition. Easy installation, comfortable handling and quiet performance are just a few of the benefits you will find with the installation of Driveworks Hub & Bearing assemblies. The Hub & Bearings come complete with wheel studs, hub and bearings. Also, includes ABS Wheel Sensors where applicable.
Back To Top
Bolt Circle Diameter:4.527 in
Bolt Size:M12X1.75
Brake Pilot Diameter:2.781 in
Hub Pilot Diameter:3.596
Wheel Pilot Diameter:2.761 in

REVIEW SNAPSHOT®

by PowerReviews
DriveworksHub & Bearing Assembly
 
3.7

(based on 3 reviews)

Ratings Distribution

  • 5 Stars

     

    (0)

  • 4 Stars

     

    (2)

  • 3 Stars

     

    (1)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

100%

of respondents would recommend this to a friend.

Pros

No Pros

Cons

No Cons

Best Uses

No Best Uses
    • Was this a gift?:
    • No (3)

Reviewed by 3 customers

Displaying reviews 1-3

Back to top

 
4.0

I would buy this product again

By 

from Accokeek, MD

See all my reviews

Verified Buyer
3 or more reviews submitted

Comments about Driveworks Hub & Bearing Assembly:

Part was easy to install

  • Was this a gift?:
  • No
 
4.0

Excellent value

By 

from Franklin TN

About Me Experienced DIY

See all my reviews

Ask me a question

Verified Buyer
3 or more reviews submitted

Pros

  • Good Value
  • Perfect OEM match

Cons

    Best Uses

    • Cadillac SRX

    Comments about Driveworks Hub & Bearing Assembly:

    Excellent value, perfect match. Only debate is whether this 1 yr warranty hub assy equals the American-made 3 yr hub assy, long-term.

    • Was this a gift?:
    • No

    (4 of 4 customers found this review helpful)

     
    3.0

    Good quality, good value

    By 

    from Franklin TN

    About Me Long-time DIY

    See all my reviews

    Ask me a question

    3 or more reviews submitted

    Pros

    • Good Value
    • OEM Quality

    Cons

    • 1 yr warranty

    Best Uses

    • Cadillac SRX

    Comments about Driveworks Hub & Bearing Assembly:

    Bought the "off-brand" version to save money. I am concerned about this 1 yr warranty vs. 3yr for the more expensive American-made part. Got $30 off using the ES123 code. Part was a perfect fit. Only odd thing was that the only instructions were in Spanish. Blank on the other side. Bought two hubs, both only had Spanish instructions so I don't think it was an oversight. Simple to install. Would have been nice if it included the torque specs. Very simple to install. Loosen the axle nut (36MM Caddy SRX) and lug nuts while on the ground. Put on a jack stand and remove the wheel. Remove the brake caliper, then the SRX caliper mount. Unbolt the rotor. Disconnect the ABS sensor. Then there are 3 hub assy bolts in the back holding the hub and dust shield on. Spray some Rust Eater on the splines and mounting surfaces. Insert a screwdriver or chisel between the hub and mounting face and tap to break hub free. Tap the axle shaft with the axle nut at the end of the shaft using a wood block for damage control. Make sure all of the old hub comes out. The inner seal remained and had to be pushed out from the back in our case. Clean and grease all mounting surfaces and splines. Install in reverse sequence. Use Loc-Tite on hub and caliper mounting bracket bolts. Push axle back and to the right in order to insert ABS sensor connector. I lightly lubed the new wheel mounting studs.

    • Was this a gift?:
    • No

    Displaying reviews 1-3

    Back to top

    Do you have questions about this product?

     

    Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

    1 Question | 1 Answer
    Displaying question 1
    • Q:

      there is no axle on my front of 2006 Cadillac srx,will this bearing still work,and is there a video that shows how to do,or something I can read how to do
      Asked on 5/23/2015 by bo

      1 answer

      • CUSTOMER CARE

        A:

        Happy to help you with your question Bo! This does show to be an exact fit for your 06 Cadillac SRX BUT for the AWD. You mentioned that you have no front axles so the wheel hub you will need for the RWD will be Part No NT513197.

        Answered on 5/23/2015 by Panda from AAP
    Displaying question 1

    Do you have a question about this product? 

    Check out the specials in our monthly flyer.
     
     
    Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.