HUB and Bearing Assembly
Hover over the image to zoom in
HUB and Bearing Assembly HUB and Bearing Assembly
Share this:
Receive a Free MOOG hat by mail with purchase of any MOOG wheel bearing hub assembly. See Rebates page for details.

Driveworks HUB and Bearing Assembly

Part No. NT513189 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Sealed:Yes

REVIEW SNAPSHOT®

by PowerReviews
DriveworksHUB and Bearing Assembly
 
2.9

(based on 14 reviews)

Ratings Distribution

  • 5 Stars

     

    (3)

  • 4 Stars

     

    (3)

  • 3 Stars

     

    (3)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (5)

62%

of respondents would recommend this to a friend.

Pros

  • Easy to use (4)

Cons

  • Incompatible (4)

Best Uses

No Best Uses
    • Reviewer Profile:
    • Casual driver (6), Auto enthusiast (3), Mechanic (3)
    • Was this a gift?:
    • No (10)

Most Liked Positive Review

 

exact fit

This went on a 06 saturn vue. This assembly was a exact fit down to the sensor position everything. Seems like a quality piece so far. I did both sides (this is highly...Read complete review

This went on a 06 saturn vue. This assembly was a exact fit down to the sensor position everything. Seems like a quality piece so far. I did both sides (this is highly recommended), the reason why is bearings can play against each other. For instance if one side is damaged and you replace it. The other bearing's on the other side are most likely going to be worn as well, or be worn enough to cause adverse effects on the other side the just got fixed. So for the saturn, be prepared to have mapp gas (yellow can) does not cost much or at the least a good propane torch (once again does not cost very much). penetrating lubricant did not help me at all I prefer the "heat and bang" method. This consists of cocking the wheel all the way one way and heating up a corner of the hub (where it connects to the housing), and beating it with a 5lb sledge yes a big boy will be vital because you need leverage. Give it a couple good blows, and then rotate the wheel the other way and do the same thing over, and over until the piece comes off (yes it will eventually come off). 9 out of 10 you will need to bend the shield out of the way, because you will end up damaging it (this happens anyway it's a shield though, just bend it back the best you can). The sledge hammer can be difficult to control so take your time on this project it is really frustrating if you work to much at once. Take brakes with the sledge it is easy to get careless. Good luck and enjoy a quality product.

VS

Most Liked Negative Review

 

Doesn't fit!!

Bolts on but axle doesn't fit in it, it flops....and the only comparable part is over $300!!!

Bolts on but axle doesn't fit in it, it flops....and the only comparable part is over $300!!!

Reviewed by 14 customers

Displaying reviews 1-10

Back to top

Previous | Next »

 
4.0

Affordable and got the job done!!

By 

from Atlanta

Verified Buyer

Comments about Driveworks HUB and Bearing Assembly:

Price was great.

 
5.0

exact fit

By 

from Indianapolis, IN

About Me Auto Enthusiast, Casual Driver, Competitive Driver, Mechanic, Truck Enthusiast, WELDER

See all my reviews

Ask me a question

3 or more reviews submitted

Pros

  • Exact Fitment
  • Sensor Included

Cons

  • Check Fitment

Best Uses

  • Large Cars
  • SUV

Comments about Driveworks HUB and Bearing Assembly:

This went on a 06 saturn vue. This assembly was a exact fit down to the sensor position everything. Seems like a quality piece so far. I did both sides (this is highly recommended), the reason why is bearings can play against each other. For instance if one side is damaged and you replace it. The other bearing's on the other side are most likely going to be worn as well, or be worn enough to cause adverse effects on the other side the just got fixed. So for the saturn, be prepared to have mapp gas (yellow can) does not cost much or at the least a good propane torch (once again does not cost very much). penetrating lubricant did not help me at all I prefer the "heat and bang" method. This consists of cocking the wheel all the way one way and heating up a corner of the hub (where it connects to the housing), and beating it with a 5lb sledge yes a big boy will be vital because you need leverage. Give it a couple good blows, and then rotate the wheel the other way and do the same thing over, and over until the piece comes off (yes it will eventually come off). 9 out of 10 you will need to bend the shield out of the way, because you will end up damaging it (this happens anyway it's a shield though, just bend it back the best you can). The sledge hammer can be difficult to control so take your time on this project it is really frustrating if you work to much at once. Take brakes with the sledge it is easy to get careless. Good luck and enjoy a quality product.

  • Was this a gift?:
  • No

(1 of 1 customers found this review helpful)

 
1.0

hmmmm.......

By 

from Lancaster, Ohio

About Me Auto Enthusiast

Pros

    Cons

    • Flimsy

    Best Uses

    • PAPERWEIGHT

    Comments about Driveworks HUB and Bearing Assembly:

    1yr waranty....because they wear out at 13 months! byers beware!

    • Was this a gift?:
    • No
     
    1.0

    DOES NOT fit 2007 Pontiac Torrent

    By 

    from Virginia

    About Me Casual Driver

    Pros

    • Didnt Get To Use Dont Kno

    Cons

    • Incompatible

    Best Uses

      Comments about Driveworks HUB and Bearing Assembly:

      Got old one off, cleaned all corrosion off the mounting area, mounted new one, the axle was smaller than the hub. :( Took most of a day for a part that was not right from the manufacturer

      • Was this a gift?:
      • No
       
      4.0

      Worthy!

      By 

      from Warwick, RI

      About Me Casual Driver

      See all my reviews

      Verified Buyer
      3 or more reviews submitted

      Pros

      • Durable
      • Versatile

      Cons

      • Not so easy to install

      Best Uses

      • Awd

      Comments about Driveworks HUB and Bearing Assembly:

      Worthy product for the money! Advance Auto Parts even loaned us some tools for free to install the product. Great deal, and will recommend to all!!

      • Was this a gift?:
      • No
       
      5.0

      Nice and Easy!

      By 

      from Pataskala, Ohio

      About Me Female

      Verified Buyer

      Pros

      • Easy To Use
      • Online Discount Was Great

      Cons

        Best Uses

          Comments about Driveworks HUB and Bearing Assembly:

          I loved the ability to search online for the exact part needed. It was easy to use and the online discount was unbeatable!!

          • Was this a gift?:
          • No
           
          5.0

          I am satisfied with my purchase.

          By 

          from Bloomingdale,Georgia

          About Me Casual Driver

          Verified Buyer

          Pros

          • Durable
          • Easy To Use

          Cons

            Best Uses

            • Trucks

            Comments about Driveworks HUB and Bearing Assembly:

            I like the idea of purchasing online and getting a 40% discount.

            • Was this a gift?:
            • No
             
            1.0

            wont fit

            By 

            from knox, in

            About Me Mechanic

            Verified Buyer

            Pros

              Cons

              • Incompatible

              Best Uses

                Comments about Driveworks HUB and Bearing Assembly:

                says it fits a 2008 torrent but not.

                • Was this a gift?:
                • No
                 
                3.0

                Price was right

                By 

                from Buffalo, NY

                Verified Buyer

                Comments about Driveworks HUB and Bearing Assembly:

                I only drive the car I don't fix it. Bought what I was told to get.

                 
                1.0

                This Hub will not fit

                By 

                from Castile, NY

                About Me Auto Enthusiast, Mechanic, Truck Enthusiast

                Pros

                • Easy To Use

                Cons

                • Incompatible

                Best Uses

                  Comments about Driveworks HUB and Bearing Assembly:

                  Had to buy the more expensive bearing in order to fit

                  • Was this a gift?:
                  • No

                  Displaying reviews 1-10

                  Back to top

                  Previous | Next »

                  Do you have questions about this product?

                   

                  Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

                  6 Questions | 9 Answers
                  Displaying questions 1-6
                  • Q:

                    Does this come with the ABS wheel speed sensor?
                    Asked on 3/28/2016 by Angela from United States

                    1 answer

                    • CUSTOMER CARE

                      A:

                      Good question, Angela! Yes, this HUB and Bearing Assembly - Part No. NT513189 comes with the ABS sensor.

                      Answered on 3/29/2016 by Solomon from AAP
                  • Q:

                    What tools do you need to remove and replace front hub from a 2005 Equinox.
                    Asked on 3/14/2015 by Lucinda

                    4 answers

                    • CUSTOMER CARE

                      A:

                      Hi Lucinda, happy to help you! These are the common tools to replace this Driveworks HUB and Bearing Assembly Part No. NT513189 are floor jack, jack stand, wheel chock, half-inch drive breaking bar, complete metric or standard (depending on vehicle) half-inch drive socket set, spindle nut socket (usually 36 millimeter), half-inch drive ratchet, large straight-edged screwdriver, sandpaper (medium to light grade), bungee cord, large rubber mallet, slide hammer, c-clamp, and half-inch drive adjustable torque wrench (recommended).

                      Answered on 3/14/2015 by Solomon
                    • CUSTOMER CARE

                      A:

                      Hi Lucinda, happy to help you! These are the common tools to replace this Driveworks HUB and Bearing Assembly Part No. NT513189 are floor jack, jack stand, wheel chock, half-inch drive breaking bar, complete metric or standard (depending on vehicle) half-inch drive socket set, spindle nut socket (usually 36 millimeter), half-inch drive ratchet, large straight-edged screwdriver, sandpaper (medium to light grade), bungee cord, large rubber mallet, slide hammer, c-clamp, and half-inch drive adjustable torque wrench (recommended).

                      Answered on 3/14/2015 by Solomon
                    • CUSTOMER CARE

                      A:

                      Hi Lucinda, happy to help you! These are the common tools to replace this Driveworks HUB and Bearing Assembly Part No. NT513189 are floor jack, jack stand, wheel chock, half-inch drive breaking bar, complete metric or standard (depending on vehicle) half-inch drive socket set, spindle nut socket (usually 36 millimeter), half-inch drive ratchet, large straight-edged screwdriver, sandpaper (medium to light grade), bungee cord, large rubber mallet, slide hammer, c-clamp, and half-inch drive adjustable torque wrench (recommended).

                      Answered on 3/14/2015 by Solomon
                    • CUSTOMER CARE

                      A:

                      Hi Lucinda, happy to help you! The tools to replace this Driveworks HUB and Bearing Assembly Part No. NT513189 are floor jack, jack stand, wheel chock, half-inch drive breaking bar, complete metric or standard (depending on vehicle) half-inch drive socket set, spindle nut socket (usually 36 millimeter), half-inch drive ratchet, large straight-edged screwdriver, sandpaper (medium to light grade), bungee cord, large rubber mallet, slide hammer, c-clamp, and half-inch drive adjustable torque wrench (recommended).

                      Answered on 3/14/2015 by Solomon
                  • Q:

                    Is there any need for special tools to replace?
                    Asked on 10/11/2014 by viking from ny

                    1 answer

                    • CUSTOMER CARE

                      A:

                      Hi Viking, glad to assist you! Few thing you would need when replacing this part are floor jack, jack stand, wheel chock, half-inch drive breaking bar, complete metric or standard (depending on vehicle) half-inch drive socket set, spindle nut socket (usually 36 millimeter), half-inch drive ratchet, large straight-edged screwdriver, sandpaper (medium to light grade), bungee cord, large rubber mallet, slide hammer, c-clamp, and half-inch drive adjustable torque wrench (recommended).

                      Answered on 10/12/2014 by Steve from AAP
                  • Q:

                    I have a 2004 Saturn Vue 4 cylinder. Will this fit it?
                    Asked on 7/24/2014 by Joey from Abilene, Tx

                    1 answer

                    • CUSTOMER CARE

                      A:

                      Hi Joey, glad to assist you! This hub assembly is an exact fit for your vehicle.

                      Answered on 7/26/2014 by Vincent from AAP
                  • Q:

                    is the same hub assy used for both the left side and right side??
                    Asked on 1/3/2014 by jb from near oxford ms

                    1 answer

                    • CUSTOMER CARE

                      A:

                      Hi jb, great question! Yes, this hub assembly is for front and it can be used for either front driver's side or passenger's side.

                      Answered on 1/5/2014 by Vincent from AAP
                  • Q:

                    Was offered to buy this product not the better one and I had not looked at the one we replaced all ready on the front end on the left side we bought the 161.99 one for the left 3 yr. warranty and now we have a 129.99 and 1 year warranty onthe other Thanks Advance for nothing.
                    Asked on 3/4/2012 by NETTIE from FORT WAYNE IN.

                    1 answer

                    • CUSTOMER CARE

                      A:

                      Please feel free to call 1-877-238-2623 and one of our representatives will gladly assist you with any questions or concerns you may have.

                      Answered on 3/5/2012 by Steve from AAP
                  Displaying questions 1-6

                  Do you have a question about this product? 

                  Check out the specials in our monthly flyer.
                   
                   
                  Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.