Water Pump - New
Hover over the image to zoom in
Water Pump - New Water Pump - New
Share this:

CARQUEST Water Pump - New

Part No. T2135 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Each Tough One water pump is engineered by an expert team to keep your cooling system in optimal running condition. Each pump is built to stringent OE specifications by an OE manufacturer and is 100% factory tested, so you are guaranteed the highest quality product. All pumps are boxed with tri-lingual instructions, application specific information sheets and necessary hardware to get the job done.

Product Features:
  • This pump is used on accessory belt driven applications
  • Fits applications with pressed on style pulley, special removal and installation tools will be necessary to remove the water pump from the vehicle and transfer pulley
  • All gaskets or seals necessary for installation are supplied with pump
  • Durable housing features precisely-machined mounting surfaces for proper sealing
  • The latest impeller upgrades engineered for maximum coolant flow
Back To Top
Fan Clutch Included:Yes
Gasket Type:Paper
Gaskets Included:Yes
Grade:OEM Standard
Heavy Duty Pump:No
Impeller Vane Quantity:6
Installation Hardware Included:One Gasket
Material:Aluminum
Mounting Hole Quantity:9
New Or Remanufactured:New
OE Number(s):10004037
Package Contents:One Pump, One Gasket
Pulley Included:No
Pump Flow:OE Equivalent
Rotation:Standard rotation - Same as crankshaft
Water Pump Drive Type:Accessory belt

Do you have questions about this product?

 

Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

2 Questions | 2 Answers
Displaying questions 1-2
  • Q:

    how do you change a water pump on a 1986 buick sklark custom 4cylinder tech 4 engine
    Asked on 9/30/2012 by jay smith from cincinnati,ohio

    1 answer

    • CUSTOMER CARE

      A:

      Instructions to replace a water pump: 1. Raise the hood on your Buick. Disconnect the negative battery cable with a socket wrench and then remove the radiator cap. Slide a coolant drain pan beneath the radiator directly under the drain plug. Loosen the drain plug by turning it counterclockwise until coolant starts to flow out of the radiator. Allow the coolant to completely drain then close the drain plug. 2. Locate the water pump on the side of the engine. It sits directly below the alternator. Squeeze the little tabs together on the spring tension clamp on the radiator hose connected to the water pump with a pair of pliers. Drag the clamp back on the hose 5 inches. 3. Slide the coolant drain pan over so that it's beneath the water pump. Pull the radiator hose off its connection on the water pump. Allow any remaining coolant in the hose to drain into the drain pan below. 4. Locate the small tensioner pulley. It mounts just above and to the left of the water pump, between the alternator and the power steering pump. Place an 18-mm box end wrench over the nut on the face of the tensioner pulley. Rotate the pulley upward to relieve its tension on the serpentine belt and then take the belt off the water pump's pulley, only. Release the tensioner pulley and remove the wrench. 5. Remove the four bolts holding the water pump's pulley in place with your socket wrench. Set the bolts and the pulley to the side of your work area. 6. Remove the eight bolts from around the base of the water pump with your socket wrench. Place all of the bolts in a safe location separated from the pulley's bolts. 7. Pull the water pump away from the side of the engine using both hands. If its seal does not come off with it use a plastic putty knife to scrape the seal off the mounting area. Discard the seal and set the old water pump to the side of your work area. Wipe down the water pump's mounting area with a shop rag. For further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and one of our representatives would be more than happy to assist you.

      Answered on 10/1/2012 by Steve from AAP
  • Q:

    how do you remove the pully
    Asked on 9/30/2012 by jay smith from cincinnati,ohio

    1 answer

    • CUSTOMER CARE

      A:

      For further assistance regarding the ToughOne or GMB New Water Pump (Part# 130-1050), please provide the year, make, model and engine size of your vehicle. This information would help us to assist you in a better way. You can also call us at:
      1-877-238-2623 or visit the nearest Advance Auto store and one of our representatives will gladly assist you with any questions or concerns you may have.

      Answered on 9/30/2012 by Rick from AAP
Displaying questions 1-2

Do you have a question about this product? 

Check out the specials in our monthly flyer.
 
 
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.