Flanged Vented CW Blower Motor w/ Wheel
Hover over the image to zoom in
Share this:

CARQUEST Flanged Vented CW Blower Motor w/ Wheel

Part No. 75739 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Please note: Advance Auto Parts is proud to carry comparable exact-fit parts from multiple vendors, as such, the item you receive may be one of two quality brands. Both brands meet the same fitment requirements and are equal in their performance and specifications.

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Factory Air.

Product Features:
  • Meets or exceeds OE design and performance
  • Magnetic size and properties compare or exceed OEM
  • Windings meet or exceed OEM specifications
  • Motor RPM equivalent to or exceeds OEM motor
Back To Top
Connector Type:2 Lead Wires
Dual Shaft:No
Flange:Yes
Motor Diameter:3 in
Motor Length:4-3/4 in
O.E.M. Replacement:Yes
Rotation:CW
Shaft Diameter:5/16 in
Shaft Length:1-1/4 in
Vented:Yes
Voltage:12 VDC
Wheel(s) Included:Yes
Wire Or Terminal Connection:2 Lead Wires

REVIEW SNAPSHOT®

by PowerReviews
ToughOneFlanged Vented CW Blower Motor w/ Wheel
 
4.3

(based on 42 reviews)

Ratings Distribution

  • 5 Stars

     

    (25)

  • 4 Stars

     

    (10)

  • 3 Stars

     

    (4)

  • 2 Stars

     

    (1)

  • 1 Stars

     

    (2)

95%

of respondents would recommend this to a friend.

Pros

  • Easy to install (17)
  • Durable (11)
  • Lightweight (10)

Cons

  • Difficult to install (9)

Best Uses

  • Replacement (23)
  • Everyday driving (15)
    • Car & Truck:
    • Casual driver (5)
    • Reviewer Profile:
    • Casual driver (15), Auto enthusiast (8), Mechanic (4)

Most Liked Positive Review

 

Great part, tough install because of 1 screw

I put this product on a 2005 Dodge Caravan. This is a great product. It works as advertised. It is a good factory replacement. However, there are five screws that must be...Read complete review

I put this product on a 2005 Dodge Caravan. This is a great product. It works as advertised. It is a good factory replacement. However, there are five screws that must be removed to get the housing off before you can access the motor. The housing is held on with five screws. Screws one through four are simple, but there is a fifth screw in the back between the firewall and the housing, it is an absolute beast to get to. You will have to remove carpet and installation from the floorboard in order to get to it, not that big of a deal, but keep this in mind. Even then, the screw is an absolute nightmare. You can touch it, you can almost see it , but you're not going to get a normal 8 mm socket on it. I would recommend purchasing a flexible screwdriver extension, or some sort of NASA invented adapter. I can't even tell you how I finally got it on and off. I just kept using every combination of adapters and extension arms that I had before I finally was able to get it, and it was still a beast. There are a couple of online videos that show people talking about this infamous fifth screw. They aren't kidding. They share the same sentiments that I have shared with you. It's not impossible, but it definitely will make you cuss. Don't shy away from this project because of that screw, but make sure you do your homework beforehand and know what you're getting yourself into and how you are going to have to access it. Also very important, when you put the housing back on , when finishing the job, make sure that you put the recirculation shield all the way to the right(non-recirculate/outside air.) This is the factory default position, and if you don't have it all the way to the right, your recirculate on your air conditioner will not work. I will include a video by someone other than myself, that goes through a pretty good job of explaining this. It is vital that you watch videos on what I have highlighted above before you attempt this job. I will also include a picture of these housing screws from the Haynes manual, but even the Haynes manual says "not pictured" for the fourth and fifth screw. You know it's bad when Haynes can't even show you a picture of it. The Haynes manual has them listed as #1 mounting fasteners.

VS

Most Liked Negative Review

 

Photo is wrong connector CHECK B4 BUYING

If you are buying this part for a Chrysler/Dodge/Plymouth vehicle - open the box and check the electrical connector carefully. The part photo shown on this web site as of...Read complete review

If you are buying this part for a Chrysler/Dodge/Plymouth vehicle - open the box and check the electrical connector carefully. The part photo shown on this web site as of 8/14/2010 shows the WRONG gender connector and green/yellow wiring. The WRONG connector is the one already on the vehicle harness - it has a flush face with two entry slots for flat blade contacts.
The correct connector face is a cavity with two flat blade contacts set deep inside.
Also - for the particular sample this reviewer purchased the wiring was too short to reach even if it had been the correct connector. The segment between the motor and the grommet was too short to reach the housing wall AND the sleeved segment was too short to reach from the groomet to the vehicle connector even if it had been the correct connector.
If for some reason you absolutely must use this part and cannot get one that is wired correctly you will have to rework it. You will need barrel crimp connectors and a stripping/crimping tool. On the old motor being replaced - remove the two screws holding the motor to the frame. Untwist the blue and black wires to allow the motor to back out of the frame. Cut the wires close to the motor. Do not disassemble the new motor. Cut the wiring between the motor and the gromet close to the grommet. Splice the wiring (black to green and yellow to blue) using barrel crimp connectors. Plug into vehicle harvess and holding fan turn it on low briefly to check that it rotates in the correct direction. If incorrect, cut, swap, and re-splice.

Reviewed by 42 customers

Displaying reviews 1-10

Back to top

Previous | Next »

 
3.0

Good fit for my vehicle, with one exception

By 

from Frederick, MD

See all my reviews

Verified Buyer
3 or more reviews submitted

Pros

  • Motorfan Runs Smooth

Cons

  • Wrong Harness Connector

Best Uses

    Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

    Used this motor/fan to as a replacement in my 1998 Plymouth Grand Voyager. Motor fits and runs great, however the electrical connector is not correct for my vehicle. I believe the connector on the motor fits 2001 and later vehicles. If you have a 1996 thru 2000 vehicle you will likely need to splice in the connector from the old motor. Not really a big deal, I used barrel crimps and taped them up good w/ heavy duty electrical tape. I'd recommend testing the motor first before cutting off the connector, using short pieces of wire to jumper from vehicle to motor connectors, as once you cut the wires you may not be able to return the motor. Make sure you get polarity correct when spicing the wires. Black wire on the motor is positive.

     
    5.0

    Perfect fit! Works beautifully! Thanks AdvanceAuto!

    By 

    from Chesterfield, VA

    About Me Casual Driver

    Verified Buyer

    Pros

    • Durable
    • Lightweight

    Cons

    • Installation Challenging

    Best Uses

    • Keep Cool Air Flowing

    Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

    Installing the blower motor was a challenge. I'd never done this type of installation. Once completed the product is performing very well. The product was an exact fit for my vehicle.

     
    5.0

    So far so good...

    By 

    from NC

    Verified Buyer

    Pros

    • Perfect fit

    Cons

      Best Uses

        Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

        Works well

         
        4.0

        Quality part.

        By 

        from Charlottesville Va

        About Me Auto Enthusiast

        Verified Buyer

        Pros

        • In Stock

        Cons

        • Tricky To Install

        Best Uses

        • Replacement

        Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

        Good part. Ok price. Tricky to install due to placement. Midget socket set and 8mm wrench a dire necessity. Works like a charm.

        (2 of 2 customers found this review helpful)

         
        5.0

        Great part, tough install because of 1 screw

        By 

        from midwest

        About Me Casual Driver

        Pros

        • Durable
        • Lightweight
        • Provides Smooth Shifting

        Cons

        • Difficult To Install

        Best Uses

        • Everyday Driving

        Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

        I put this product on a 2005 Dodge Caravan. This is a great product. It works as advertised. It is a good factory replacement. However, there are five screws that must be removed to get the housing off before you can access the motor. The housing is held on with five screws. Screws one through four are simple, but there is a fifth screw in the back between the firewall and the housing, it is an absolute beast to get to. You will have to remove carpet and installation from the floorboard in order to get to it, not that big of a deal, but keep this in mind. Even then, the screw is an absolute nightmare. You can touch it, you can almost see it , but you're not going to get a normal 8 mm socket on it. I would recommend purchasing a flexible screwdriver extension, or some sort of NASA invented adapter. I can't even tell you how I finally got it on and off. I just kept using every combination of adapters and extension arms that I had before I finally was able to get it, and it was still a beast. There are a couple of online videos that show people talking about this infamous fifth screw. They aren't kidding. They share the same sentiments that I have shared with you. It's not impossible, but it definitely will make you cuss. Don't shy away from this project because of that screw, but make sure you do your homework beforehand and know what you're getting yourself into and how you are going to have to access it. Also very important, when you put the housing back on , when finishing the job, make sure that you put the recirculation shield all the way to the right(non-recirculate/outside air.) This is the factory default position, and if you don't have it all the way to the right, your recirculate on your air conditioner will not work. I will include a video by someone other than myself, that goes through a pretty good job of explaining this. It is vital that you watch videos on what I have highlighted above before you attempt this job. I will also include a picture of these housing screws from the Haynes manual, but even the Haynes manual says "not pictured" for the fourth and fifth screw. You know it's bad when Haynes can't even show you a picture of it. The Haynes manual has them listed as #1 mounting fasteners.

         
        5.0

        Worked great

        By 

        from Lower Burrell Pa.

        About Me Auto Enthusiast

        Pros

        • Easy To Install
        • Lightweight

        Cons

          Best Uses

          • Everyday Driving

          Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

          Fit as a replacement should! Everything lined up and worked.

          (1 of 1 customers found this review helpful)

           
          5.0

          Direct fit for 01-07, requires connector mods for 96-2000

          By 

          from Huntsville, AL

          See all my reviews

          Ask me a question

          3 or more reviews submitted

          Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

          I've replaced four of these blower motors in the '01-07 vans now. First, they are direct fit for the '01-'07 vans; the '96-2000 vans require connector modifications for this blower to fit. Just be aware of that. Second, the one screw in the back can be felt by hand but very hard to see. As has been said, remove the floor mat, pull back the carpet, and don't be afraid to remove a bit of the insulation up there so you can get to it. When you reinstall the bottom of the housing, be sure to take pliers and pull the fresh air / recirc door DOWN to fully seat it into the bottom housing. The end must stick out, not be flush. There are three grabber fingers which must fit into a groove on that door. Take a look and you'll see what I mean. NOW... if your van is a 2001-2002, Chrysler used thicker padding in those vans, and it makes it a little tougher to see where that bolt is. ALSO on the 2001-2002s; once I had removed every screw I needed to, that housing STILL wouldn't come down and I ended up just yanking down and breaking it. It broke on the cabin air intake grid so not a big deal. I just replaced the motor, lined up the bottom and put it back into place, put all the screws in, and everything's fine. If somebody figures out where that sneaky extra bolt is on the 2001-2002s, post it up. The bottom of the blower housing was also different than the '03-04s I worked on.

           
          5.0

          Friend need help A/C not blowing at all Wife is HOT need fix

          By 

          from Millington TN

          About Me 16 Years Chrysler Dodge, Auto Enthusiast, Mechanic, Truck Enthusiast

          Pros

          • Chilly Breezes Asap
          • Durable
          • Easy To Install
          • Happy Wife
          • Lightweight

          Cons

          • Be Careful Sharp Edges
          • Forget About That 5th One
          • Only 5 Screwes 8mm

          Best Uses

          • Lots Cool Breeze Smooth
          • Replacement

          Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

          Looked on line and found all parts and Hepa cabin filter in stock Outstanding Tested resistor block and check wiring good small 8mm wrench and socket in and out 15 minutes Good job Friend so Happy me too. Thanks wonderful folks of my Advance Team I hope next few months I can sign up to work Part time too Perfect OE replacement at very good price

          (2 of 4 customers found this review helpful)

           
          2.0

          Wrong Connector

          By 

          from Greenville, SC

          About Me Casual Driver

          Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

          Wrong side of correct connector. Original out of '98 Plymouth G Voyager has female, the replacement has male. So, save the old to replace the new. Wiring is lighter weight than original. Besides the connector issue, relatively easy install. Pulling back the the carpet from the firewall gives just enough extra working room to make it very simple.

          (2 of 4 customers found this review helpful)

           
          5.0

          works great

          By 

          from va beach

          About Me Casual Driver

          Verified Buyer

          Pros

          • Easy To Install

          Cons

            Best Uses

            • Everyday Driving

            Comments about ToughOne Flanged Vented CW Blower Motor w/ Wheel:

            great find

            Displaying reviews 1-10

            Back to top

            Previous | Next »

            Do you have questions about this product?

             

            Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

            10 Questions | 11 Answers
            Displaying questions 1-10
            • Q:

              Purchased a blower motor #75739 for a 2000 Chrysler Voyager SE. The wire connector is incorrect. If I replace the connector with the connector from the replaced motor will it effect the warranty?
              Asked on 12/12/2015 by Butch

              1 answer

              • CUSTOMER CARE

                A:

                Hi Butch, I'm glad to assist you. It is possible that this may void the warranty of your motor. I would recommend you to contact the store where you have purchased the motor.

                Answered on 12/14/2015 by Steve from AAP
            • Q:

              Product Application: 2000 Chrysler Voyager SE - Blower Motor, Front, w/ Wheel; Requires use of O.E. Connector. What is a O.E. Connector?
              Asked on 12/12/2015 by Woody from Fond du Lac, WI

              1 answer

              • CUSTOMER CARE

                A:

                Hi Woody, I'm glad to assist you. It is recommended to use the factory connector along with this ToughOne or Factory Flanged Vented CW Blower Motor w/ Wheel (Part No. 75739). Otherwise you can use the connector which was built according to the exact replacement specs of the Original Equipment Manufacturer.

                Answered on 12/14/2015 by Steve from AAP
            • Q:

              How long to install blower motor in dodge grand caravan
              Asked on 11/12/2014 by vicki from gladstone, missouri

              1 answer

              • CUSTOMER CARE

                A:

                Hi Vicki, good question! It depends upon the skill level of the person performing the operation. For help with your project, I recommend purchasing a Haynes repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts.

                Answered on 11/13/2014 by Solomon
            • Q:

              Where is the front air blower motor for a dodge grand Caravan.
              Asked on 7/7/2013 by Wally from Wellington, Fl.

              1 answer

              • CUSTOMER CARE

                A:

                This Factory Air Blower Motor - Part No. 75739 is located on the passenger side of your Dodge Grand Caravan under the instrument panel. For any further assistance, please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

                Answered on 7/8/2013 by Morgan from AAP
            • Q:

              I have a 2002 Dodge Caravan. Front heater/ac blower has 92) screw tabs (not 3) ... what is the correct blower fan ? Where is the control resistor located (for fan speed) ??

              Thanks.

              Bruce
              Asked on 8/2/2012 by Cold Raabe from De Tour Village, MI

              1 answer

              • CUSTOMER CARE

                A:

                The Blower Motor Resistor on your 2002 Dodge Caravan should be located in the heater box, right behind the glove box. Sorry, right now we are unable to locate the blower fan for your 2002 Dodge Caravan online. However, if you could please visit your nearest Advance Auto store or call us directly at 1-877-ADVANCE (238-2623) and one of our representatives there would be more than happy to assist you.

                Answered on 8/2/2012 by Vincent from AAP
            • Q:

              I have a 2004 pacifica and the heat just stopped blowing the blower in the back is still working is this the blower or somethingelse.
              Asked on 2/8/2011 by Leo from Tappahannock, VA

              1 answer

              • CUSTOMER CARE

                A:

                I would suggest taking your vehicle to a certified mechanic for a proper diagnosis before buying and having parts installed that may not (solve/be) the problem.

                Answered on 2/8/2011 by David the Dynamite Parts Guy from AAP
            • Q:

              I have a 2003 T&C 6 cyl 3.8 the front air and heat does not work would this be the blower for the front? I have changed the blower resistor and checked the Blower Relay and nothing still. The blower has not worked in weeks and today my battery died and when I got the battery jumbed it started working but as soon as I turned off my van it quit again and now comes on and off at random times and when it is on it will roast you out of the van. The blower does not sound good it sounds like it is trying to kick off and sounds sick
              Asked on 12/13/2010 by V from St Charles MO

              1 answer

              • CUSTOMER CARE

                A:

                This sounds like it would be a bad blower motor. However, with out the presence of your vehicle we would not be able to properly diagnose it nor provide you with a 100% answer. We would suggest taking your vehicle to a certified mechanic for a proper diagnosis before buying and having parts installed that may not solve or be the problem.

                Answered on 12/13/2010 by Ron the Auto Parts Rebel from AAP
            • Q:

              where is this located
              Asked on 12/2/2010 by Ja from greenfield ohio

              1 answer

              • CUSTOMER CARE

                A:

                For further assistance, please provide the year, make, model and engine size of your vehicle

                Answered on 12/2/2010 by Mike the Auto Parts Master from AAP
            • Q:

              on my 2006 town&country were is my bwd blower motor risistor located?
              Asked on 7/1/2010 by kid dale from buffalo ny

              2 answers

              • CUSTOMER CARE

                A:

                To best answer your question please purchase a Haynes repair manual for your vehicle.

                Answered on 7/8/2010 by Paul
              • A:

                IF your T&C has automatic temperature control (you set the temperature as a number) then it doesn't have a resistor block, it has a power module located just behind the glove box on the HVAC shell.
                If your T&C has the traditional warmer-cooler sliders and a 4 speed switch then it has a resistor block also located just behind the glove box on the HVAC shell. If your vehicle were an earlier model, the resistor block would be on the other side of the firewall from the glove box, in the engine compartment.

                Answered on 8/14/2010 by Polychrome from Boston, MA
            • Q:

              I need to know if front and rear fan blowers are the same for chrysler pacifica 2004?
              Asked on 6/26/2010 by frank from woonsocket,R.I.

              1 answer

              • A:

                The front and rear blowers on the 2004 Pacifica are completely different. The front blower is a single shaft and wheel. The rear is a double shaft motor spinning two wheels. The Chrysler service manual says that the assembly is balanced as a set, and therefore the OEM replaces the motor and wheel together instead of replacing just the motor or a wheel.

                Answered on 8/14/2010 by Polychrome from Boston, MA
            Displaying questions 1-10

            Do you have a question about this product? 

            Check out the specials in our monthly flyer.
             
             
            Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.