TECHnovation Clutch Slave Cylinder
Hover over the image to zoom in
Share this:

CARQUEST Clutch TECHnovation Clutch Slave Cylinder

Part No. 37723 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Designed and engineered for faster installation than original equipment using existing lines and no special tools. OEM plastic cylinders can be prone to cracking/breakage. TECHnovation Clutch Hydraulics aluminum castings are made from solid blocks that are bored and honed for accurate tolerances and maximum durability.
Back To Top
Bore Size:1 in
Inlet Size(s):10 mm

REVIEW SNAPSHOT®

by PowerReviews
CARQUEST ClutchTECHnovation Clutch Slave Cylinder
 
4.3

(based on 4 reviews)

Ratings Distribution

  • 5 Stars

     

    (2)

  • 4 Stars

     

    (1)

  • 3 Stars

     

    (1)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

100%

of respondents would recommend this to a friend.

Reviewed by 4 customers

Displaying reviews 1-4

Back to top

 
4.0

Good product fit right

By 

from Salisbury Maryland

Verified Buyer

Comments about CARQUEST Clutch TECHnovation Clutch Slave Cylinder:

To repair the truck

Comment on this reviewHelp Icon

 
3.0

Bleeding instructions

By 

from PA

About Me Auto Enthusiast

Verified Buyer

Pros

  • Provides Smooth Shifting

Cons

    Best Uses

    • Everyday Driving

    Comments about CARQUEST Clutch TECHnovation Clutch Slave Cylinder:

    The bleeding instructions are useless. It refers to using the same method as brakes, and assumes there's a similar type bleed fitting - there is not. Best way to bleed is to remove the entire system intact (Master cylinder, reservoir and slave cylinder) and bleed by hand as its all hanging from a hook.

    Comment on this reviewHelp Icon

     
    5.0

    This is a great product

    By 

    from Chesapeake, VA

    About Me Casual Driver

    See all my reviews

    Verified Buyer
    3 or more reviews submitted

    Pros

    • Durable
    • Easy To Install
    • Lightweight
    • Made Of Aluninum
    • Provides Smooth Shifting

    Cons

      Best Uses

      • Everyday Driving

      Comments about CARQUEST Clutch TECHnovation Clutch Slave Cylinder:

      I bought the master cylinder & slave cylinder since the old ones were original '83 equipment. These units reuse the original High pressure hose. Provided were new O-rings and new retaining pins. Bleeding the system is the most tedious procedure. I found that by filling and bleeding the master cylinder per the instructions, then attaching the hose was the way to go. I used a new clean plastic syringe that came with an ethanol additive product worked well to fill the hose. The nozzle was small enough to fit into the hose and made the job a lot easier. Then bled and attached the slave cylinder.

      Comment on this reviewHelp Icon

      (0 of 1 customers found this review helpful)

       
      5.0

      I would buy this product again

      By 

      from Renovo,PA

      Verified Buyer

      Pros

      • Easy To Install

      Cons

        Best Uses

          Comments about CARQUEST Clutch TECHnovation Clutch Slave Cylinder:

          It is well made.

          Comment on this reviewHelp Icon

          Displaying reviews 1-4

          Back to top

          Do you have questions about this product?

           

          Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

          6 Questions | 7 Answers
          Displaying questions 1-6
          • Q:

            The slave cylinder mounted exactly as the old one did, however the hydraulic line enters into the end of the cylinder and right beside it is an alan screw. Is this supposed to be a bleeder screw? If it is, I could not get it open. Could it possibly be defective? If not, how are you supposed to bleed the system properly?
            Asked on 12/10/2011 by Anonymous from Reading, PA

            2 answers

            • CUSTOMER CARE

              A:

              The required information has been sent to the mail address provided.

              Answered on 12/12/2011 by Vincent from AAP
            • A:

              pump up the systemand hold the pedle down and take the lid off so the air bubbles go away

              Answered on 11/14/2012 by justoldfords from laurel hill fl.
          • Q:

            HOW YOU DO YOU PRIME THE CLUTCH AFTER REPLACING THIS PART.
            Asked on 5/4/2011 by Kay from Interlachen fl

            1 answer

            • CUSTOMER CARE

              A:

              I would suggest taking your vehicle to a certified mechanic for a proper diagnosis before buying and having parts installed that may not (solve/be) the problem.

              Answered on 6/25/2011 by Steve from AAP
          • Q:

            the haynes manual says that 1987 and earlier the exteral slave cylinder and master cylinder are a sealed set and you cant replace the slave cylinder itself and is not available separately it also says that it can't be bleed due that it is a sealed system and after looking at the slave there is no bleeder valve. so maybe you could tell me how to bleed a sealed system? and you sell both parts separately how would you bleed this system after installed the slave and mater into the truck ?
            Asked on 2/19/2011 by Gary from Elizabeth co

            1 answer

            • CUSTOMER CARE

              A:

              I would suggest taking your vehicle to a certified mechanic for a proper installation.

              Answered on 2/21/2011 by David the Dynamite Parts Guy from AAP
          • Q:

            I need the rubber boot that goes over the bell housing can I buy just this?
            Asked on 12/11/2010 by paulr from Philadelphia Ms.

            1 answer

            • CUSTOMER CARE

              A:

              For further assistance, I recommend going into one of our stores, they may be able to help you better.

              Answered on 12/23/2010 by Mike the Auto Parts Master from AAP
          • Q:

            i put a new one on my 1987 ford truck but we are having trouble getting the system bled,did we do something wrong ?
            Asked on 7/3/2010 by gator from knoxville tennessee

            1 answer

            • CUSTOMER CARE

              A:

              As long as everything was hooked up ok, it should be able to be bled just fine.

              Answered on 7/8/2010 by Mike from AAP
          • Q:

            I am looking for the mounting clips to install this part. The original ones broke when the old slave cylinder was removed.
            Asked on 5/3/2010 by tbdrummer from carlisle, pa

            1 answer

            • CUSTOMER CARE

              A:

              We do not have those clips listed online. You may have to check out one of our local Advance Auto Parts stores to see if they can locate them for you.

              Answered on 7/13/2010 by Mike from AAP
          Displaying questions 1-6

          Do you have a question about this product? 

          Check out the specials in our monthly flyer.
           
           
          Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.