Belt Tensioner
Hover over the image to zoom in
Share this:

CARQUEST by Dayco Belt Tensioner

Part No. 89288 Warranty Details  

See if this part fits a specific vehicle.

Check Vehicle Fit

Dayco No Slack Automatic Belt Tensioners are specifically built to outperform and outlast competitive OE parts. Each component is built to resist rust, endure the toughest of conditions while promoting quieter performance and longer life.

Product Features:
  • Manufactured with a specially coated patented flat wire spring to allow the internal tension to be concentric, thus providing a more even degree of constant tension
  • The heavy duty cast aluminum spring case resists cracking and fatigue
  • The required plastic elbows & o-rings are included
  • Made in the USA
Back To Top
Belt Type:Serpentine
Mounting Type:Automatic, Integral
Pulley Diameter:76 in
Pulley Material:Steel
Pulley Type:Flat
Pulley Width:31 in

REVIEW SNAPSHOT®

by PowerReviews
CARQUEST by DaycoBelt Tensioner
 
3.2

(based on 13 reviews)

Ratings Distribution

  • 5 Stars

     

    (2)

  • 4 Stars

     

    (6)

  • 3 Stars

     

    (1)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (4)

69%

of respondents would recommend this to a friend.

Pros

  • Easy to install (3)

Cons

No Cons

Best Uses

  • Replacement (6)
  • Everyday driving (3)
    • Reviewer Profile:
    • Auto enthusiast (4), Casual driver (3), Mechanic (3)

Most Liked Positive Review

 

"No slack" in my drive belt system

Dayco is a premier manufacturer of drive belt parts. They make excellent belts which I've used for years and so I was confident their tensioner would be of the utmost quality (and it...Read complete review

Dayco is a premier manufacturer of drive belt parts. They make excellent belts which I've used for years and so I was confident their tensioner would be of the utmost quality (and it is) best of all, Dayco makes their products in the USA.
This tensioner was needed to replace a less then 2-month-old Dorman unit in which the tensioner arm completely sheared off the bracket during use. Being an emergency purchase, I didn't care about brand assuming it wasn't another Dorman. Luckily, I found this one at AA. It installs easy, fits well and performs perfectly. I like the metal pulley over the OE plastic one as well. The kit comes complete with heater elbow and seals for FWD cars. I gave it 4 stars (4.5 would have been more appropriate) because it lacks the proper seals for a RWD car's heater hoses. I had to travel to my local hardware store to find the proper thickness o-rings as the one's included are for FWD cars and WILL NOT work on a RWD application. Aside from that, I am very happy I bought this unit and have no idea why there are negative past reviews.

VS

Most Liked Negative Review

 

DOESN"T LAST..... POOR QUALITY

I have installed this product on a 1997 Buick LeSabre 3800 V6 engine. After a short period of use, the tensioner wears and the pulley begins to misallign the belt. The belt then...Read complete review

I have installed this product on a 1997 Buick LeSabre 3800 V6 engine. After a short period of use, the tensioner wears and the pulley begins to misallign the belt. The belt then begins to track near the edge of the tensioner pulley. If you hit a puddle of water when driving in wet weather the belt comes off. I have had this problem with 3 of these........ I installed an AC Delco OEM tensioner and now have no problems. This tensioner is JUNK. Relpace with OEM.

Reviewed by 13 customers

Displaying reviews 1-10

Back to top

Previous | Next »

 
4.0

Some Experience Necessary!

By 

from Kissimmee, FL

Verified Buyer

Pros

  • Almost Oem But Not Quite

Cons

  • Issues With Heater Hoses

Best Uses

    Comments about CARQUEST by Dayco Belt Tensioner:

    This is a good part and installs fairly straight-forward, but it has several issues and you will need to be aware of these! One is the heater hose connections, which will require a few good-sized washers with a larger diameter center hole to shim the space between the Buick hose retainer screw and the screw area on the new part. This happens often in Chinese-made product, as they dont 'get it right' and why I wonder!

    The instructions are vague and sketchy at best, but you might get lucky! Check the web for further educational videos (You Tube is great) and watch for the hard parts like where the old plastic insert tube breaks inside the engine! It must be removed before installing the new tensioner, but it is not as hard as one might imagine! Good luck!

    • Was this a gift?:
    • No

    Comment on this reviewHelp Icon

     
    5.0

    Better Then OEM

    By 

    from Toledo Ohio

    Verified Buyer

    Comments about CARQUEST by Dayco Belt Tensioner:

    A lot lighter than the factory one and more smooth spinning. Looks more heavy duty without the weight.

    Comment on this reviewHelp Icon

     
    3.0

    Good and Bad Part

    By 

    from Madison Heights, MI

    About Me Auto Enthusiast

    Pros

    • Works For Now

    Cons

    • Idler Pully Noise

    Best Uses

    • Replacement

    Comments about CARQUEST by Dayco Belt Tensioner:

    1998 Oldsmobile Intrigue, 3.8L.

    Before I started working on my car, I didn't need this part. I only wanted to replace the common $3 90 degree plastic elbow that went to this part/engine. Unfortunately, I wasn't paying attention when pulling this part to get at the elbow and broke the aluminum fitting that plugs into the block on the the back of this tensioner. One of the reasons I wasn't careful was the replacement elbow came with two different ones and I thought the other one was getting replaced and was where I couldn't see it. Sadly I was mistaken.

    So I found this part on Rock Auto but wanted it now. I ordered online and picked up at the store. Though it cost me $30 more than Rock.

    It looks to be a great part to replace one you broke the fitting on. However, like all the other reviews, my idler pulley makes noise.

    I put my old one on and it was quite. I went back to the new one with the old fastener, because I though the problem could have been the washer they have on there, as opposed to the factory. It still makes noise, I suspect the bearing isn't made for the load as it's quiet at idle and gets louder when it's loaded more.

    I'm planning on getting a good quality idler pulley/bearing later, and I have my original as a spare for now.

    In summary, this part looks to be a good replacement for the original, if you brake your fitting replacing the $3 elbow. the arm and spring seem to be good. However, I would not trust the pulley.

    I recommend this part with that exception.

    Comment on this reviewHelp Icon

     
    1.0

    Does not live up to expectations!

    Profile Image

    By 

    from central VA

    About Me Auto Enthusiast, Diy When Possible

    See all my reviews

    Ask me a question

    3 or more reviews submitted

    Pros

    • Looks good

    Cons

    • Difficult To Install
    • Fails Quickly
    • Not Worth The Price

    Best Uses

    • Replacement

    Comments about CARQUEST by Dayco Belt Tensioner:

    Installed on 9/7/13 and just 6 months and 7,200 miles it makes more noise than the original did with 136,000 miles on it. And yes, I carefully checke the pully alignments when installed. I am going to put a new pully on the original and reinstall it!

    Comment on this reviewHelp Icon

     
    4.0

    Looks good

    Profile Image

    By 

    from central VA

    About Me Casual Driver

    See all my reviews

    Ask me a question

    Verified Buyer
    3 or more reviews submitted

    Pros

    • Lightweight

    Cons

    • Difficult To Install

    Best Uses

    • Replacement

    Comments about CARQUEST by Dayco Belt Tensioner:

    Just installed this 9/7/13. This is something I would not reccommend to a novice due to the level of difficulty and knowledge needed. As to durability and quality all I hhave to go on are Dayco's claims from their web site. I have only put about 26 miles on the car since installing it.

    Comment on this reviewHelp Icon

     
    4.0

    Quality

    By 

    from Cincinnati, OH

    About Me Casual Driver

    Pros

    • Easy To Install

    Cons

    • Need O Rings For Rwd

    Best Uses

    • Everyday Driving
    • Replacement

    Comments about CARQUEST by Dayco Belt Tensioner:

    Very easy installation it just needs RWD O-rings. You really don't need to drain the coolant; some will leak out, just buy a gallon and top it off when you finish.

    Comment on this reviewHelp Icon

     
    4.0

    1st part defective but exchanged easily

    By 

    from Pearland TX

    About Me Mechanic

    Verified Buyer

    Pros

    • Easy To Install

    Cons

    • 1st Part Was Defective

    Best Uses

    • Replacement

    Comments about CARQUEST by Dayco Belt Tensioner:

    1st part defective but was exchanged for good part with no problems

    Comment on this reviewHelp Icon

     
    4.0

    Part works great with a small upgrade

    By 

    from Long Island, NY

    About Me Auto Enthusiast, Mechanic

    Pros

    • Durable

    Cons

      Best Uses

      • Everyday Driving

      Comments about CARQUEST by Dayco Belt Tensioner:

      I installed the belt tensioner approx. 6 months ago and recently began getting squeaking noise in the morning on damp or rainy days. I noticed that the belt was sitting on the edge of the pulley. My girlfriend drove it about a month ago and hit a puddle and the belt came off. That was the only time this happened. I recently removed the pulley and installed a washer to adjust it approx. 2-3mm and now the belt sits in the middle of the pulley and no more squeaking. Based on the location of the belt, I doubt it will come off from another puddle. A new part should not have to be shimmed, but I have learned after 20 years of working on vehicles, it makes sense to make sure the part fits properly whether it is new or reman.

      Comment on this reviewHelp Icon

      (2 of 2 customers found this review helpful)

       
      4.0

      "No slack" in my drive belt system

      By 

      from New Jersey

      About Me Auto Enthusiast, Casual Driver, Mechanic

      Pros

      • Easy To Install
      • Improves Engine Efficiency
      • Lightweight

      Cons

      • Lacks Seals For Rwd

      Best Uses

      • Everyday Driving
      • Performance Driving
      • Racing
      • Replacement
      • Restoration

      Comments about CARQUEST by Dayco Belt Tensioner:

      Dayco is a premier manufacturer of drive belt parts. They make excellent belts which I've used for years and so I was confident their tensioner would be of the utmost quality (and it is) best of all, Dayco makes their products in the USA.
      This tensioner was needed to replace a less then 2-month-old Dorman unit in which the tensioner arm completely sheared off the bracket during use. Being an emergency purchase, I didn't care about brand assuming it wasn't another Dorman. Luckily, I found this one at AA. It installs easy, fits well and performs perfectly. I like the metal pulley over the OE plastic one as well. The kit comes complete with heater elbow and seals for FWD cars. I gave it 4 stars (4.5 would have been more appropriate) because it lacks the proper seals for a RWD car's heater hoses. I had to travel to my local hardware store to find the proper thickness o-rings as the one's included are for FWD cars and WILL NOT work on a RWD application. Aside from that, I am very happy I bought this unit and have no idea why there are negative past reviews.

      Comment on this reviewHelp Icon

      (1 of 2 customers found this review helpful)

       
      5.0

      No Problems At All

      By 

      from Pittsburgh, PA

      About Me Fairly mechanical

      See all my reviews

      Helpful Reviewer

      Pros

      • Same as oriiginal
      • Works great

      Cons

      • GM design sucks

      Best Uses

        Comments about CARQUEST by Dayco Belt Tensioner:

        Product works great. Ford tensioners are much easier to change. What was GM thinking making the belt tensioner part of the cooling system. Had to beat with rubber hammer to loosen and a piece of origial broke and was hard to get out. Keep track of the orings that come in plastic bag. I don't know why others are having problems. Mine went on fine and is still going strong. No wetness issues. It's a bad job no matter which suppliers unit you put in but I can't think of why rain is an issue.

        Comment on this reviewHelp Icon

        Displaying reviews 1-10

        Back to top

        Previous | Next »

        Do you have questions about this product?

         

        Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

        8 Questions | 9 Answers
        Displaying questions 1-8
        • Q:

          Ok so i replaced my tensioner assembly i put the tensioner and everything back together but now my belt has all this extra room. Did i do something wrong or is it my belt.
          Asked on 3/20/2013 by Jervel from United States

          1 answer

          • CUSTOMER CARE

            A:

            Sorry, without the presence of your vehicle we would not be able to properly diagnose it nor provide you with a 100% answer. We would suggest that you take your vehicle to a certified mechanic for further diagnosis. For any further assistance, please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

            Answered on 3/21/2013 by Steve from AAP
        • Q:

          How do you remove the belt tensioner and replace all the hoses and parts needed for a 1997 buick lasebra with 3800 engine? Please help that you:
          Asked on 1/16/2011 by coltmaster from panama city, florida

          1 answer

          • CUSTOMER CARE

            A:

            I would suggest taking your vehicle to a certified mechanic for a proper installation.

            Answered on 2/11/2011 by David the Dynamite Parts Guy from AAP
        • Q:

          How do you remove this belt tensioner?
          Asked on 1/16/2011 by coltmaster from florida

          1 answer

          • CUSTOMER CARE

            A:

            For step by step instructions I recommend that you go to your nearest Advance Auto Parts store and purchase a repair manual.

            Answered on 2/11/2011 by David the Dynamite Parts Guy from AAP
        • Q:

          do you have the hoses that go on the belt tensioner of a 98 camaro 3.8 automatic. I think the ports are called water ducts. They dont have anything to do with the belt tensioner activity.
          Asked on 11/29/2010 by Ram from Pflugerville tx

          1 answer

          • CUSTOMER CARE

            A:

            Those hoses are called heater hoses. We do not have those for your vehicle.

            Answered on 11/30/2010 by Mike the Auto Parts Master from AAP
        • Q:

          do you have the hoses that connect to the water ports and what are they called? Thanks Ram
          Asked on 11/28/2010 by RAM from Pflugerville TX

          1 answer

          • CUSTOMER CARE

            A:

            For further assistance, please provide the year, make, model and engine size of your vehicle

            Answered on 11/29/2010 by Mike the Auto Parts Master from AAP
        • Q:

          What size o-rings do you need to install (re-install) this part? I need the sizes for the plastic elbow, the lower insert and the heater hoses if you have them....
          Asked on 11/17/2010 by Doug from Y-Town, OH

          1 answer

          • CUSTOMER CARE

            A:

            I would recommend purchasing a Haynes repair manual for your vehicle. This will have many of the specifications needed for a variety of repairs.

            Answered on 1/12/2011 by Anonymous
        • Q:

          is this easy to put on ?
          Asked on 8/7/2010 by dboy da kid..BUICK ALL DAY from SOUF EAST DC

          1 answer

          • CUSTOMER CARE

            A:

            For step by step instructions i recommend that you go to your nearest Advance Auto Parts store and purchase a repair manual.

            Answered on 8/7/2010 by Kevin from AAP
        • Q:

          why does this one look differant from the factory assembly
          Asked on 1/17/2010 by madmax from union sc

          2 answers

          • A:

            aftermarket part

            Answered on 3/11/2010 by yamama from uranus
          • A:

            because the factory part is junk and this one is a better design on how the tensioner attached to the body of the plate and won't come apart like the factory one

            Answered on 7/2/2010 by gm is junk from wilkes-barre, pa
        Displaying questions 1-8

        Do you have a question about this product? 

        Check out the specials in our monthly flyer.
         
         
        Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.