100 PSI Replacement Oil Pressure Sensor
Hover over the image to zoom in
Share this:

Autometer 100 PSI Replacement Oil Pressure Sensor

Part No. 2242 Warranty Details  

Fit of this part varies by vehicle & equipment specs Type of Fit

For use with short sweep electric oil pressure gauges. 1/8" NPT Male Thread. Includes 1/4" NPT adapter fitting.
Back To Top
Height (in.):3"
Width (in.):2"

Do you have questions about this product?(earn points for answers!)

 

Ask a question, get answers from real customers and in-house experts. Or contact Customer Care by email or call 1-877-238-2623.

48 Questions | 49 Answers
Displaying questions 1-10Previous | Next »
  • Q:

    Where is the oil pressure sensor located om a 1996 corolla. 1.6 l
    Asked on 3/17/2015 by Tim from Naperville, IL

    1 answer

    • CUSTOMER CARE

      A:

      Hi Tim, I'm glad to help you! On 1996 Toyota Corolla, the oil pressure sensor is located left to the oil filter.

      Answered on 3/18/2015 by Solomon
  • Q:

    Where is the oil sensor located on a 2005 Jeep Liberty 3.7L engine? How do you replace this part?
    Asked on 3/9/2015 by Ashleigh from United States

    1 answer

    • CUSTOMER CARE

      A:

      Hi Ashleigh, glad to assist you! The oil pressure sensor is located just above the oil filter on the 3.7-liter engine of the Jeep Liberty. Here is the instructions to replace this part. Raise the front of your Liberty with a jack. Position a set of jack stands under the Jeep so that they firmly support the weight of the vehicle. Turn the front wheels all the way to the right, and remove the push-in fasteners that secure the right side front splash shield to the fender. You can use a trim stick or large flat screwdriver to remove the fasteners. Once you have removed the fasteners, you can pull off the splash shield. Reach into the engine compartment through the wheel opening and locate the oil pressure switch just above the oil filter. Remove the electrical connector on the back of the switch by depressing the locking tab and pulling the connector straight off the switch. Remove the switch using a wrench, turning the switch counterclockwise until it comes out of the engine block. Install the new switch into the engine block and tighten it with your wrench. Install the electrical connector onto the new switch. Push it straight onto the switch and listen or feel for the locking tab to snap onto the switch, ensuring the connector is locked in place. Reinstall the right side splash guard into the fender opening and push the plastic push-in fasteners into the holes in the fender well. Raise the Jeep with the jack and remove the jack stands. Lower the Jeep to the ground and start the engine. Check the gauges to ensure that the new switch is functioning.

      Answered on 3/10/2015 by Steve from AAP
  • Q:

    where is the oil pressure sensor located on a 2005 GMC Sierra 1500? Is it easy to get to and replace?
    Asked on 2/11/2015 by NAC2 from Metro Detroit

    1 answer

    • CUSTOMER CARE

      A:

      Hi NAC2, glad to help you! The Oil Pressure Sensor is located on the top rear driver side of the engine. You will need a oil pressure sensor socket to remove the sensor. It depends upon the skill level of the person performing the operation. For help with your project, I recommend purchasing a Haynes or Chilton repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts. The repair manual part number is 24066.

      Answered on 2/12/2015 by Steve from AAP
  • Q:

    where is the oil pressure sensor located on a 2007, silverado truck?
    Asked on 12/13/2014 by jc from BISCOE, N.C. 27209

    1 answer

    • CUSTOMER CARE

      A:

      Hi Jc, I'm glad to help you! The Oil Pressure Sensor is located on the block behind the intake manifold.

      Answered on 12/14/2014 by Solomon
  • Q:

    would this fit a 2003 Saab 9-3 Convertible? It has the 2.0L engine
    Asked on 12/9/2014 by jayc04 from Loveland, CO

    1 answer

    • CUSTOMER CARE

      A:

      Hi Jayc04! This will not fit your 2003 Saab 9-3 Convertible. Currently, the exact oil pressure sensor for your vehicle is unavailable online.

      Answered on 12/9/2014 by Solomon
  • Q:

    this '' replacement ' part does not look like the original,is there an electrical adapter or am i lookin at the wrong one.
    Asked on 12/1/2014 by tony from lasvegas nevada

    1 answer

    • CUSTOMER CARE

      A:

      Hi Tony, I'm glad to assist you! The part numbers for the sending unit for an oil pressure short sweep electrical gauge is #2242 and for a full sweep it would be #2246. The full sweep gauge will feature a 3 wire harness running out to the gauge.

      Answered on 12/2/2014 by Solomon
  • Q:

    Where is the oil pressure sensor located on a 1998 mazda 626 2.5l v6
    Asked on 9/8/2014 by Dave from Rhode island

    1 answer

    • CUSTOMER CARE

      A:

      Hi Dave, I'm happy to assist you! The oil pressure sensor is connected to your engine block. It has two wires connected to it and one is directly linked to the oil pressure gauge located on your dashboard. The sensor is typically located at the front of your engine block near the fuel filter and close to the intake manifold. However, check your owner's manual to confirm its actual location.

      Answered on 9/9/2014 by Vincent from AAP
  • Q:

    Where is the the oil pressure sensor located on 1996 Chevy s10? Do you need a special tool to remove it?
    Asked on 7/27/2014 by Mendybeth

    1 answer

    • CUSTOMER CARE

      A:

      Hi Mendybeth, happy to help you! It is located under the hood, passenger side lower engine area, above the oil pan. To replace the oil pressure sensor, you will need a socket set, a torque wrench, an oil filter, an adjustable wrench, a drainage basin, and new oil.

      Answered on 7/29/2014 by Vincent from AAP
  • Q:

    Where is the oil pressure sensor on 97 deville
    Asked on 5/3/2014 by chuck-d from atlanta ga.

    1 answer

    • CUSTOMER CARE

      A:

      Hi chuck-d, glad to assist! It is located under the hood, on the drivers side of the engine, right behind the oil filter.

      Answered on 5/4/2014 by Vincent from AAP
  • Q:

    Where is the Oil Pressure Sensor for a 2007 Chevy Avalanche?
    Asked on 3/18/2013 by Tuddie from Ohio

    1 answer

    • CUSTOMER CARE

      A:

      With reference to your inquiry on the Autometer 100 PSI Replacement Oil Pressure Sensor - part# 2242, the oil pressure sensor on your Chevy Avalanche would be located on the top [center to right] rear of motor. For any further assistance, please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

      Answered on 3/18/2013 by Vincent from AAP
Displaying questions 1-10Previous | Next »

Do you have a question about this product? 

Create or view your online garage

Check out the specials in our monthly flyer

 
 
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.