100 PSI Replacement Oil Pressure Sensor
Hover over the image to zoom in
Share this:

Autometer 100 PSI Replacement Oil Pressure Sensor

Part No. 2242 Warranty Details  

Fit of this part varies by vehicle & equipment specs Type of Fit

For use with short sweep electric oil pressure gauges. 1/8" NPT Male Thread. Includes 1/4" NPT adapter fitting.
Back To Top
Height:3"
Width:2"

Do you have questions about this product?

 

Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

52 Questions | 53 Answers
Displaying questions 1-10Previous | Next »
  • Q:

    1997 buick skylark oil pressure sending unit sensor location
    Asked on 12/3/2016 by scot

    1 answer

    • CUSTOMER CARE

      A:

      Hi Scot, glad to assist you! For most of the vehicle models, the oil pressure sensor is typically located near the bottom, right side of an engine, between the oil filter and the oil pan. However, the oil pressure sensor, also known as the oil pressure switch or sender, has different locations depending on a vehicle's make. The exact location of the oil pressure sensor on your 1997 Buick Skylark can be found in the vehicles owner's manual or by contacting the manufacturer directly.

      Answered on 12/4/2016 by Solomon from AAP
  • Q:

    Where is the Oil Pressure/Temperature Sensor located in a 2006 Ford Five Hundred SE AWD? Will this part work for my 2006 Ford Five Hundred SE AWD? The Ford part number is 7F9Z-4B487-A. Does this part include a new seal? Thank you!
    Asked on 7/21/2016 by WisFarmGirl from Superior, WI

    1 answer

    • CUSTOMER CARE

      A:

      Hi WisFarmGirl, happy to help! The Oil Pressure sensor/sender on a Ford Five Hundred SE AWD is located at the lower left front of the engine, on the backside of the oil filter adaptor to be specific. The exact fit sender is the Wells Vehicle Electronics Oil Pressure Switch Part # PS409. On your second question, the Ford part number 7F9Z-4B487-A, it shows as a Axle differential sensor. I would recommend that you check with a certified mechanic for a proper diagnoses before buying the part that might/might not solve the issue.

      Answered on 8/12/2016 by John the Car-Doc from AAP
  • Q:

    where is located on a2005 gmc envoy l6
    Asked on 8/15/2015 by wayne

    1 answer

    • CUSTOMER CARE

      A:

      Hi Wayne, I'm glad to assist you. The oil pressure switch on your 2005 GMC Envoy should be located right above the oil filter, attached to the oil filter adapter housing.

      Answered on 8/15/2015 by Steve from AAP
  • Q:

    Q: Where is the oil pressure sensor located om a Pontiac montana sv6 3.9
    Asked on 3/31/2015 by Joseph

    1 answer

    • CUSTOMER CARE

      A:

      Hi Joseph, happy to help you! The oil pressure sensor is located right above the oil filter. You will need to access from under the vehicle after removing the starter motor. For help with your project, I recommend purchasing a Haynes or Chilton repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts.

      Answered on 3/31/2015 by Steve from AAP
  • Q:

    Where is the oil pressure sensor located om a 1996 corolla. 1.6 l
    Asked on 3/17/2015 by Tim from Naperville, IL

    1 answer

    • CUSTOMER CARE

      A:

      Hi Tim, I'm glad to help you! On 1996 Toyota Corolla, the oil pressure sensor is located left to the oil filter.

      Answered on 3/18/2015 by Solomon
  • Q:

    Where is the oil sensor located on a 2005 Jeep Liberty 3.7L engine? How do you replace this part?
    Asked on 3/9/2015 by Ashleigh from United States

    1 answer

    • CUSTOMER CARE

      A:

      Hi Ashleigh, glad to assist you! The oil pressure sensor is located just above the oil filter on the 3.7-liter engine of the Jeep Liberty. Here is the instructions to replace this part. Raise the front of your Liberty with a jack. Position a set of jack stands under the Jeep so that they firmly support the weight of the vehicle. Turn the front wheels all the way to the right, and remove the push-in fasteners that secure the right side front splash shield to the fender. You can use a trim stick or large flat screwdriver to remove the fasteners. Once you have removed the fasteners, you can pull off the splash shield. Reach into the engine compartment through the wheel opening and locate the oil pressure switch just above the oil filter. Remove the electrical connector on the back of the switch by depressing the locking tab and pulling the connector straight off the switch. Remove the switch using a wrench, turning the switch counterclockwise until it comes out of the engine block. Install the new switch into the engine block and tighten it with your wrench. Install the electrical connector onto the new switch. Push it straight onto the switch and listen or feel for the locking tab to snap onto the switch, ensuring the connector is locked in place. Reinstall the right side splash guard into the fender opening and push the plastic push-in fasteners into the holes in the fender well. Raise the Jeep with the jack and remove the jack stands. Lower the Jeep to the ground and start the engine. Check the gauges to ensure that the new switch is functioning.

      Answered on 3/10/2015 by Steve from AAP
  • Q:

    where is the oil pressure sensor located on a 2005 GMC Sierra 1500? Is it easy to get to and replace?
    Asked on 2/11/2015 by NAC2 from Metro Detroit

    1 answer

    • CUSTOMER CARE

      A:

      Hi NAC2, glad to help you! The Oil Pressure Sensor is located on the top rear driver side of the engine. You will need a oil pressure sensor socket to remove the sensor. It depends upon the skill level of the person performing the operation. For help with your project, I recommend purchasing a Haynes or Chilton repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts. The repair manual part number is 24066.

      Answered on 2/12/2015 by Steve from AAP
  • Q:

    where is the oil pressure sensor located on a 2007, silverado truck?
    Asked on 12/13/2014 by jc from BISCOE, N.C. 27209

    1 answer

    • CUSTOMER CARE

      A:

      Hi Jc, I'm glad to help you! The Oil Pressure Sensor is located on the block behind the intake manifold.

      Answered on 12/14/2014 by Solomon
  • Q:

    would this fit a 2003 Saab 9-3 Convertible? It has the 2.0L engine
    Asked on 12/9/2014 by jayc04 from Loveland, CO

    1 answer

    • CUSTOMER CARE

      A:

      Hi Jayc04! This will not fit your 2003 Saab 9-3 Convertible. Currently, the exact oil pressure sensor for your vehicle is unavailable online.

      Answered on 12/9/2014 by Solomon
  • Q:

    this '' replacement ' part does not look like the original,is there an electrical adapter or am i lookin at the wrong one.
    Asked on 12/1/2014 by tony from lasvegas nevada

    1 answer

    • CUSTOMER CARE

      A:

      Hi Tony, I'm glad to assist you! The part numbers for the sending unit for an oil pressure short sweep electrical gauge is #2242 and for a full sweep it would be #2246. The full sweep gauge will feature a 3 wire harness running out to the gauge.

      Answered on 12/2/2014 by Solomon
Displaying questions 1-10Previous | Next »

Do you have a question about this product? 

Check out the specials in our monthly flyer.
 
 
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.