Reduced Friction Ball Bearing Tube Cutter to Fuel Pump Module Assembly

• Each gasket, set, or seal is built to meet or exceed all original equipment specifications and is validated for fit, form, and function
• Application specific design to ensure a perfect fit and correct operation for unsurpassed quality that you can trust
• FEL-PRO gasket sets are engineered and manufactured specifically for the aftermarket repair environment
• Every part for the repair procedure is included in the kit unless otherwise noted

• Unit is designed to OE fit, form and function requirements accomplished by leveraging our expertise
• Direct fit ensures safe, secure fuel tank installation
• Product individually packaged and labeled to help reduce product damage prior to installation
• Industry leading coverage on straps for plastic tanks

• 100% computer testing ensures consistent performance.
• 100% new OE-quality seals and cups are installed to prevent leakage and ensure like-new performance and reliability. All rubber meets S.A.E. specifications.
• Cast iron master cylinders come with premium protective coating to minimize rust, extending on-car and on-shelf life.
• Piston assemblies are 100% height-gauged to meet or exceed O.E. performance.
• Bores meet critical micro-finish specifications to eliminate pitting and corrosion, which could cause premature failure.
• Plastic reservoirs are 100% vacuum-tested to ensure proper function.

• Replaceable aluminum valve stem is anodized for long-lasting corrosion resistance-and may be serviced separately from the entire unit
• Comes with stem unit, grommet, washer, and hex nut for a complete installation
• Sensors are designed to accommodate installation angles from 5 to 26 degrees
• Dorman sensors work with all existing Tire Pressure Monitoring System (TPMS) tools

• Powder coated to protect against corrosion, which can cause coil spring fatigue or fracture.
• Designed to lower stresses for longer service life.
• All coil springs are 100% load tested.
• Worn or sagging coil springs can cause premature tire wear due to vehicle misalignment.

Omix-ADA is more than just a parts manufacturer, they're a community of enthusiasts dedicated to producing the finest in off-road solutions. Our products have been propelling four-wheel drive vehicles down highways, back roads and over the world's roughest terrain for about two decades. Omix's team of engineers have developed, tested and trail ridden many of our 11,000+ products until they were perfected for you.

Omix-Ada is proud to have one of the most capable Research and Development, Engineering, and Product Design teams in the automotive aftermarket. By utilizing the latest in 3D Computer Aided Design and Finite Element Analysis, and coupling these tools with our decades of market experience, we are able to develop products that give our customers the highest value parts possible.

• Contains gaskets, o-rings, or seals to properly replace the product
• Color coded for easy identification
• Zinc coated to resist corrosion
• Vehicle specific applications

Radius corner design - to extend the life of fasteners

The design drives the side of the fastener instead of the corner

Provides increased strength, but also avoids rounding of rusted or damaged fasteners

Fully guaranteed No doubt, Sunex tools offer one of the most complete and toughest Impact Socket lines around. This socket is designed to tackle the toughest jobs with solid durability and keeps them pounding job after job. Also it features a radius corner design, causing the socket to grab the sturdy wall of the fastener instead of grabbing the corners, resulting in less wear on the fastener.

• Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE expertise
• Durable powder coating applied to exterior of oil pan for a long lasting rust free unit
• Washed and then sealed with an anti-corrosive spray on the interior for a rust free unit at installation
• Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
• Engineered to stringent tolerances based on our Canadian engineers’ in-depth knowledge of the OE part it’s designed to replace
• Road tested to ensure real world performance and to verify that each designs meets our high standards for quality
• Coating salt spray tested for over 200 hours to insure durability

In North America, Bosal designs, develops, and manufactures original equipment exhaust systems for carmakers such as GM and Ford. Bosal supplies OE service products to many import / transplant carmakers including VW, Honda, Volvo, Subaru, and Mazda. Bosal also develops high performance exhaust for OEM port of entry and dealer programs.

Bosal pioneered the manufacture of one-piece, direct-fit replacement exhaust systems more than twenty-five years ago. Today, Bosal remains the leader in direct-fit exhaust systems for import vehicles, and has expanded their program to include direct-fit catalytic converters for both the import and domestic aftermarket. Included in the catalytic converter program is their new line of Bosal Super-Cats and our most recent addition - Bosal's line of CARB Approved Catalytic Converters.

Product Features:

• One Piece, Direct Fit Unit that eliminates the need for cutting, pipe bending, or welding.

• Internal springs increased durability and enhanced stability prevents tube chafing
• Lower amperage draws less load on vehicle's electrical system
• Fuel level gold-filled sensors provide improved resistance to sulfur corrosion and heat resistance
• Empty float height and float retention is to exact OE specifications guaranteeing correct gas gauge reading