16-14 Gauge Spade Solder filled Terminal, No. 10, Blue to Taper Bearing Cone

• Available in many different styles, including PVC and weatherproof
• A large selection of wire gauges available
• Conveniently packaged in a variety of piece counts to assist with both small and large projects
• Also suitable for a broad range of industrial and commercial uses

• Problem Solver® powdered metal gusher bearing design enables grease to flow through the bearing to the stud for reduced friction and enhanced strength and stability.
• MOOG® engineered steel composition results in a stronger component.
• Full ball metal stud provides 360 degrees of smooth, consistent, rotational movement resulting in more responsive steering.
• Belleville washer preload provides lower torque and stud articulation with minimal axial clearance.
• An enlarged ball joint receptacle in the lower control arm can cause a loose ball joint fit. MOOG® Problem Solver® design includes an oversized housing for a more secure fit.

• Each unit is 100% computer tested at 3 points in the remanufacturing process to ensure great performance.
• Every motor is assembled with the precise amount of lubricant to ensure quiet operation and long life.
• Improved over O.E. - Gears are redesigned with a stronger, less brittle material than O.E. to prevent premature wear, striping and breakage, thus extending the performance life.
• Motor magnets are 100% recharged for superior performance and reliability.
• New high-quality gaskets are used in every window lift unit to prevent water entry, thus eliminating failure modes related to water penetration.

• Constant-tension spring ensures constant tension for precise alignment and steering control
• Contaminant-proof seal helps eliminate contamination that causes premature wear

• 1% new, not remanufactured
• Alignment tool included for easy installation (where applicable)
• Direct replacement for a proper fit every time
• Durable steel and plastic construction

• Conveniently packaged in a variety of sizes, assortments, and quantities
• Metal screws and nylon nuts included (where applicable)
• Tamper-proof screws provided for increased security (where applicable)
• Durable design for a long service life

• Manufactured to exacting quality and dimensional specifications for Superior Stopping Power
• Exceeds ISO manufacturing guidelines. (International Organization for Standardization)
• OE vane configuration to dissipate heat, increasing pad life.
• Proper harmonic design helps to reduce brake noise.
• Non-directional finish for less break-in time and reduced brake noise.
• Ready for immediate "out-of-the-box" installation (after cleaning)
  
  Advance Auto Parts Rotor Tips:

  • Recommend using Wearever Brake Clean to remove residual manufacturing oils prior to installation.
  • Always use a torque wrench to tighten wheel bolts to the manufacturers'' specifications to prevent pedal pulsation.
  • Always replace rotors in pairs to improve stopping power.

• Includes spring and clips (where applicable)
• Smooth or textured surface available
• Chrome-plating available (where applicable)
• Available for front and rear driver and passenger sides

• All Weather Fluid: Contains special modifiers to reduce friction and ensure smooth rod reaction.
• Rod Displaced Valving: Tuned specifically for each application, this valving automatically adjusts to road extremes to provide consistency and ride comfort.
• Fluon Banded Piston: The fluon band provides consistent sealing between the piston and pressure tube which delivers better control and increased durability.
• Unique Groove Tube - PSD: Precision tapered grooves in the pressure tube perform like an additional stage of valving for optimum ride tuning.
• Hardened and Chrome Plated Piston Rod: Long service life.
• Unique Rod Guide and Single Lip Seal: Bronze reinforced rod guide bearing and special seal provides longer service life and consistent performance.
• Nitrogen Gas Charged: For improved ride and handling, helps maintain tire to road contact by reducing aeration.
• Special Dust Boot/Jounce Bumper: Protective dust boot reduces dirt and any moisture build-up. Jounce bumper helps prevent severe suspension movement. Dust boot & jounce bumper sold separately.

• Manufactured to exacting quality and dimensional specifications for Superior Stopping Power
• Exceeds ISO manufacturing guidelines. (International Organization for Standardization)
• OE vane configuration to dissipate heat, increasing pad life.
• Proper harmonic design helps to reduce brake noise.
• Non-directional finish for less break-in time and reduced brake noise.
• Ready for immediate "out-of-the-box" installation (after cleaning)
  
  Advance Auto Parts Rotor Tips:

  • Recommend using Wearever Brake Clean to remove residual manufacturing oils prior to installation.
  • Always use a torque wrench to tighten wheel bolts to the manufacturers'' specifications to prevent pedal pulsation.
  • Always replace rotors in pairs to improve stopping power.

SCFM 10.0 @100 PSI

1/4" NPT air inlet, nozzle thread size: 7/16" - 27

Body outlet thread size: 1/2" - 27

OSHA compliant

• Steel or plastic construction for long-lasting durability against heat, shock and corrosion
• Replacement stops squeak, squeal or groaning noise associated with a worn idler pulley
• Direct replacement and direct fit idler pulleys for a trouble-free replacement
• Vehicle try-on testing and rigorous materials testing to ensure high-quality performance

• Premium Unloaded/Semi-Loaded/Loaded
• OEM Grade Rubber Components
• Correct OEM Specified Piston Material
• Essential Mounting Hardware Included
• Exclusive Rustproof Coating

The KYB Gas-a-Just monotube shock absorber has additional performance advantages over the twin-tube design: It can instantly, automatically adjust to more handling and control needs and never experiences performance fade due to aeration. The Gas-a-Just is available as an OE Monotube replacement and as an OE Twin-tube performance upgrade. The KYB Gas-a-Just has two separate working chambers: An air-free hydraulic piston & valve area for responsiveness & control and a second high-pressure Nitrogen gas area with a floating piston that provides a comfortable ride during normal driving and adds instant performance on demand. The monotube design provides the best combination when you sometimes need or want more than average or designed ride control performance and steering responsiveness. The KYB Gas-a-Just is a high pressure, Nitrogen gas-charged monotube design that includes every quality component that our global OEM products include.

Product Features:

• A heavy gauge seamless cylinder to add strength and provide a high compression sealing surface
• Application-specific cylinder bore sizes
• A precision multi-stage hydraulic valve assembly operating in an aeration-free fluid chamber
• A separate Nitrogen gas, high pressure chamber and floating piston
• Triple chrome-plated piston rod and multi-lip oil seals that reduces wear
• Solid, seamless mounting eye rings and bolt bushings that can’t separate and become noisy
• Chemically bonded insulator mounting bushings that won’t slip out
• A Teflon-coated or phenolic piston band that reduces friction and provides a positive cylinder seal
• Specially formulated hydraulic fluid with multi-range viscosity for any weather climate