Air Charge Temperature Sensor to Steel Cup-Type Expansion Plug 7/8 Inch

• Problem Solver® powdered metal gusher bearing design enables grease to flow through the bearing to the stud for reduced friction and enhanced strength and stability.
• MOOG® engineered steel composition results in a stronger component.
• Full ball metal stud provides 360 degrees of smooth, consistent, rotational movement resulting in more responsive steering.
• Belleville washer preload provides lower torque and stud articulation with minimal axial clearance.
• Greaseable socket design allows new lubricant to flush contaminants from the assembly, reducing corrosion and wear.

• Case hardened for durability and strength
• Precision machined to reduce drag and friction
• Designed to meet or exceed OE specifications

• Lifetime Warranty

• Best for intense sun locations
• Durable long-lasting fabric
• Solution dyed woven acrylic fabric
• Provides almost complete UV blockage
• 5-year warranty

• Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE expertise
• Durable powder coating applied to exterior of oil pan for a long lasting rust free unit
• Washed and then sealed with an anti-corrosive spray on the interior for a rust free unit at installation
• Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
• Engineered to stringent tolerances based on our Canadian engineers’ in-depth knowledge of the OE part it’s designed to replace
• Road tested to ensure real world performance and to verify that each designs meets our high standards for quality
• Coating salt spray tested for over 200 hours to insure durability

• Best for intense sun locations
• Durable long-lasting fabric
• Solution dyed woven acrylic fabric
• Provides almost complete UV blockage
• 5-year warranty

• Each gasket, set, or seal is built to meet or exceed all original equipment specifications and is validated for fit, form, and function
• Application specific design to ensure a perfect fit and correct operation for unsurpassed quality that you can trust
• FEL-PRO gasket sets are engineered and manufactured specifically for the aftermarket repair environment
• Every part for the repair procedure is included in the kit unless otherwise noted

• 100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
• Exclusive rust-prohibitive finishing process extends unit life.
• Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
• New mounting nuts and washers ensure proper, hassle-free installation.
• All units are 100% vacuum tested to ensure reliable performance.

SureGrip hex design drives the side of the fastener, not the corner

Made in the U.S.A.

Lifetime warranty This 12 point socket has a 1.13" diameter and is 3.25" in length.

• Designed to meet or exceed OES design requirements
• High-temperature, moisture proof, silicone boots
• Increased terminal retention and strength properties
• Features necessary accessories, silicone content and boot designs

• Inner cables are sheathed and lubricated to provide longer life and improved performance
• Flexible casings are completely covered with conduit to prevent corrosion of interior cables
• Zinc plated fittings and clips prevent corrosion
• Brackets included where applicable

No. 49884 - for Tempo/Topaz with 2" opening

No. 49885 - for Taurus/Sable with 2-1/2" opening

Weight: 1 lb., 6 oz. This set contains two wrenches for adjusting the rear toe on Ford and Mercury vehicles. One wrench fits the 1984-94 Tempo and Topaz; the other fits 1986-95 Taurus and Sable sedans, and 1986-95 FWD Continental.

• Each gasket, set, or seal is built to meet or exceed all original equipment specifications and is validated for fit, form, and function
• Application specific design to ensure a perfect fit and correct operation for unsurpassed quality that you can trust
• FEL-PRO gasket sets are engineered and manufactured specifically for the aftermarket repair environment
• Every part for the repair procedure is included in the kit unless otherwise noted

• Clean Wheels
• Ultra-quiet
• Extremely rotor-friendly
• European braking performance with an enhanced pedal feel
• Friction formula specifically designed for a European vehicle
• Ultimate upgrade for OE semi-metallic and low metallic brake pads

• Many sizes available
• Conveniently available in packs of different quantities
• Constructed from high quality steel, copper, brass, or rubber
• Dorman’s Engine Expansion Plugs are constructed to strict engineering quality standards