Cylinder Head to Genesis; Snap Tonneau

• Each gasket, set, or seal is built to meet or exceed all original equipment specifications and is validated for fit, form, and function
• Application specific design to ensure a perfect fit and correct operation for unsurpassed quality that you can trust
• FEL-PRO gasket sets are engineered and manufactured specifically for the aftermarket repair environment
• Every part for the repair procedure is included in the kit unless otherwise noted

• OEM (original equipment manufacturer)
• Precision-built for exact replacement
• 100% load and no-load tested
• High-quality construction

• Internal springs increased durability and enhanced stability prevents tube chafing
• Lower amperage draws less load on vehicle's electrical system
• Fuel level gold-filled sensors provide improved resistance to sulfur corrosion and heat resistance
• Empty float height and float retention is to exact OE specifications guaranteeing correct gas gauge reading

• Original Equipment Replacement Wires / Complete Ignition Wire Set - 7mm
• DENSO First Time Fit ignition wire sets are identical in form, fit, color, and performance to the factory-installed wire sets
• Every part the wire set's construction meets or exceeds OE/OES specifications
• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to "click" in place for a secure fit, allowing the installer to "feel and hear" that a solid connection has been made, even when the connection is in a difficult-to-see location
• Through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

• Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertise
• Product come with installation instructions, wiring harness and installation hardware where applicable
• Includes strainers for smoother installation process and ensures a clean fuel system upon replacement
• Precision tested fuel level sensor ensures vehicles fuel gauge will provide an accurate reading at any fuel level
• Tested for voltage, amperage, resistance, pressure, and volume to ensure product performance and quality
• Engineered to stringent tolerances based on our Canadian engineers’ in-depth knowledge of the OE part it’s designed to replace
• Award winning packaging; double layer walls for added strength and projection; new inflated bubble packaging-condensed individual vertical air chambers for added protection
• Engineered and developed by Spectra Premium; proud member of the A.A.S.A. fuel pump manufacturers working group

• High Performance Handling and Aggressive Good Looks
• Lower Center of Gravity
• Stop Quicker, Corner Faster and get Better MPG!
• Progressive Spring Design for Excellent Ride Quality

• Each unit is 100% computer tested at 3 points in the remanufacturing process to ensure great performance.
• Every motor is assembled with the precise amount of lubricant to ensure quiet operation and long life.
• Improved over O.E. - Gears are redesigned with a stronger, less brittle material than O.E. to prevent premature wear, striping and breakage, thus extending the performance life.
• Motor magnets are 100% recharged for superior performance and reliability.
• New high-quality gaskets are used in every window lift unit to prevent water entry, thus eliminating failure modes related to water penetration.

• Original Equipment Quality Parts
• Made in Korea
• Manufactured by ISO-14000, QS-9000, or ISO/TS-16949 certified suppliers

• Original Equipment Quality Parts
• Made in Korea
• Manufactured by ISO-14000, QS-9000, or ISO/TS-16949 certified suppliers

• Meets or exceeds OE specifications
• Delphi compressors are constructed with high-quality corrosion resistant aluminum alloy not often found in aftermarket products
• Low torque demand results in better engine performance and increased fuel economy
• All Delphi compressors are 100% leak tested and are an exact fit, resulting in easier installation and fewer comebacks
• Sealing washers are included with Delphi compressors, saving precious time during installation.

Extra recess depth and nose-down design

SureGrip hex design drives the side of the fastener, not the corner

Made in the U.S.A.

Lifetime warranty22 piece set is made in the U.S.A., featuring the SK's High Visibility technology. The sockets are coated with a rust-preventative compound, which makes them exceptionally resistant to corrosive factors. In addition to the rust-preventative coating, the sockets are laser engraved every 120 degrees with extra large markings for improved readability. All the SK impact sockets feature the SK's SureGrip hex design, which drives the side of the hex, not the corner. This not only provides increased strength, but also avoids rounding of rusted or damaged fasteners, which can occur when using a sharp cornered hex  tool. The unique nose-down design extends the taper as far as possible, for improved access over straight wall designs. Sizes include: 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm, 19mm, 20mm, 21mm, 22mm, 23mm, 24mm, 25mm, 26mm, 27mm, 28mm, 29mm, 30mm, 32mm sockets. 

• Sealed Main Body Prevents Rusting From Inside Out
• Open Back End On Receiver For Easy Cleaning
• One-Piece Collar Reduces Rust And Ensures Strength
• Exceeds V-5 Standards
• Exceeds V-5 Standards
• Robotic Welding For Superior Strength And Fit
• Limited Lifetime Warranty To Original Purchaser

• Provides A Clean Sharp Look
• Made Of Premium T-6 Aircraft Grade Billet Aluminum
• Specific Designed For Custom Fit
• Laser Technology Ensures Precision Quality
• Hassle Free Installation

• Improves Gas Mileage
• Protects Cargo
• No Drill For Easy Installation
• Heavy Duty Bows and Rails
• Integrated Rear Tailgate Seal
• Custom Fit To Application
• Includes Adapter Kit For Use On Cargo Mgmt Systems
• Limited Lifetime Warranty