Pilot Bearing Puller with 1" Reach to Hendrickson Bushing SVC Set

Built especially for inside pulling jobs, and particularly for removing flywheel pilot bearings on automobiles, trucks and tractors
Also very practical for pulling motor, generator, and magnet bearings
Reach: 1"; ID spread minimum: 7/8"; maximum: 2-1/8"

Eliminates the need to break the circuit and install a shunt; simply clamp around he cable or wire under test

Dual scale: 2-200 amps AC/DC 2-2000 amps AC/DC

Wt., 1 lb., 5 oz.

Includes two handle sizes and 41 discs, ranging from 1/2" to 3" diameter

Comes with a plastic storage box and insert Now you can have the proper size driver for nearly any automotive seal, bearing, or bushing installation job.

Made of heat treated chrome molybdenum steel
Pliers have .038" (1.0mm) diameter tips
Overall length: 3"
Handle length: 2" Small sized pliers for work in tight areas. Service S-ring and R-ring clips, internal, straight, or angled. this set includes two internal snap ring pliers (one straight and one 45 degree) and two external snap ring pliers (one straight and one 45 degree).

Especially designed to accommodate the 1-11/16 in. (43mm) wheel bearing retaining nut which is recessed into the hub. Used to remove and install the front wheel bearing retaining nut on 1994 and newer Dodge 1/2-ton pickup trucks with Dana 44 front axle and Dana 60 axle with a vacuum disconnect. Since the retaining nut is recessed, this special tool provides the depth needed. It is 1/2 in. drive, and can be used with an impact wrench.

Installing a ball joint on a lower control arm typically requires the effort of two people. However, with this tool and our OTC7420 or OTC7421 pry bar, it’s a one-person job.  

7/8" diameter
30" in length
Weight: 4 lbs., 7 oz. This Jimmy Bar is forged from chrome alloy steel and heat-treated to resist bending and breaking.

Use with OTC7507 CV joint fork and OTC1155 slide hammer to remove an axle assembly from the transaxle without causing damage to expensive aluminum transmission cases or other components
17-1/2" long
5/8" x 18 thread
Wt., 2 lbs., 7 oz.

Works on a wide range of engines, both domestic and imported

Enables you to do low and high pressure fuel system tests

Will also work with your shop's pressurized air supply for more powerful cleaning without expensive propellants Clogged fuel injectors cause sluggish engine performance, poor fuel economy, and a rough idle. You can easily correct such problems with this injector cleaning kit. Using our Pro Inject-R Kleen fluid (not included), you can effectively clean injectors, restore their spray patterns, and prevent recurring deposits. Kit includes: canister, gauge, hose, fittings and operating instructions.

The OTC Ford cam tools ensure correct cam timing when servicing timing belts, chains, head gaskets, or other valve train repairs

Ford cam tool kit for 1997 thru 2004 4.0L Explorer/Mountaineer SOHC V6 engines Contains tools OTC6478, OTC6479, OTC6480, OTC6481, OTC6482, OTC6484, OTC6485 packaged in a molded storage case.

Nemisys now includes Body and Chassis systems along with Engine, Transmission, ABS, and Airbag

Repair Information - Typical Sensor / Data Specs

Domestic OBD I and OBD II coverage (1984 thru 2008)

Asian OBD I and OBD II optional coverage (1983 thru 2008)

Enhanced OBD II Mode 6 screens Other features include: Domestic and Asian Enhanced Data and DTCs; Global OBD II Asian & European coverage (1996 thru 2008); CAN Enabled-no adapters to buy; Data Graphing; Record / Playback; Vehicle Protocols: CAN, J1850 VPM, J1850 PWM, ISO 9141, Keyword 2000, UART, SCP, SCI, CCD, and more.  2007 Domestic Kit Vehicle Coverage

GM ’84-2008

Ford ’84-2008

Chrysler ’88-2008

Jeep ’91-2008

Saturn ’91-2008 

Asian ’96-2008 (Global OBD II). 

European ’96-2008 (Global OBD II). OPTIONAL  2007 Asian Vehicle Coverage

Honda ‘85-2008

Toyota ’88-2008

Nissan ’87-2008

Mitsubishi ’88-2008

Mazda ’83-2008

Hyundai ’89--2008

Kia ’95--2008

Isuzu ’84--2008

And more Asian Systems

Head is movable from side-to-side for full off-center load pressing.

Ram-to-work distance is adjusted by a forcing screw that's extended or retracted with a speed crank.

"Open Throat" feature is great for bulky jobs, and allows ram to be mounted outside press frame.

17 1/2-ton "Open Throat" press with 201832 ram with 2" stroke, 4002 hydraulic hand pump, 9650 gauge, 9767 hose (1/4" I.D. X 6'), 32118 adjusting screw, 24814 speed crank, 28228 ram cap, and 42733-WH2 pump mounting bracket.

Weight: 284 lbs.

Application for Chrysler LH models 1993-1995
CCD 1988-1995 with 4000 Enhanced, Monitor Elite, Nemisys, Genisys
Weight: 12 oz.

Reconditioned Genisys with all the latest improvements
System 3.0
OBD II Smart Cable
USA 2008 Domestic, USA 2008 Asian, 2006 InfoTech, ABS / Airbag 2008
Includes 2009 Asian/Domestic update coupon and domestic OBD I cables Reconditioned Genisys with all the latest improvements, new deluxe carrying case and 90 day warranty. System 3.0 and new OBD II smart cable. USA 2008 Domestic, USA 2008 Asian, 2006 InfoTech, ABS / Airbag 2008.

Provides quick and easy verification of RF and IR transmitter signal with audible beep and LED light
RF example: key FOBs, garage door openers, tire pressure sensors activation tools, aftermarket key FOBs and remote starters, etc.
IR example: IR printer ports, in-vehicle audio/video remote controls. general IR remote control and signals
Designed to detect RF signals between 0-900 MHz
Operates on 9V battery (included)

Forged jaws with sure-grip teeth grab the filter for easy removal
Slip joint ratchet and lock mechanism allows a secure grip on filters ranging from 3-3/4" to 7" (95mm to 178mm) in diameter
Pliers are 18" long

Make quick work of pulling stubborn, rusted pilot bearings
The puller's forcing screw expands the jaws inside the bearing and simultaneously pushes against the crankshaft

Female: 5/8"-18
Male: 3/4"-16
Length: 2-1/4"For use on the ends of Push- Puller legs or forcing screws when pulling shafts, bearing caps, pinions, etc.

Hex profiles are one of the most common fasteners found in the automotive, industrial, and agricultural markets today
Our hex bit sockets give service professionals a tool for application from bumper to bumper on millions of vehicles
Manufacturered with premium quality tool grade steel and  as two-piece construction for even stronger performance

For Genisys owners that have System 2.0 or newer, but need a 1 GB Memory Card
System 3.0 software
High-speed commercial grade 1 GB super card
Required to install the 2008 software
These memory cards are pre-loaded with the 2008 software.  The same card used in the new Genisys EVO!
 IMPORTANT NOTE: This 1 GB memory card is required to install Domestic ’08, Asian ’08, ABS / Airbag ‘08, European, HD Standard, and InfoTech Software. The card is pre-loaded with all the latest software releases for fast and convenient installation. New model year releases require a separate software application purchase or the card will install the latest version of your current model year software.

Includes a cross slotted jaw pliers and a wide, flat band hose clamp pliers
Services most ring-type or flat-band hose clamps
Clamps are held open with a ratchet locking mechanism
Jaws swivel to access hose clamps in any position

Base, pressure cylinder, and oil reservoir form one internal part, and provide more strength and safety to these jacks
Piston never contacts cylinder, so pressure will be absorbed and not damage jack if vehicle tilts

Designed to remove and install relays, which are usually located on confined, hard-to-reach areas
Specially coated tips offer a solid grip on the relay

Works on 1994-2003 7.3 diesel engine in Ford 3/4 and 1 ton trucks
A complete kit with the tools you need to properly remove and install the rear main oil seal and wear ring on the crankshaft
Eliminates makeshift methods of seal removal and installation that could damage new seal or crankshaft

Tools, Fluids & Garage > Hand Tools > External Torx Sockets

Application: Grand Prix ABS for '98-2002

Replaces 14" and 15-1/2" clutch assemblies

Lifting range of 9" to 37"

Swivel casters provide easy maneuverability

Makes the task an easy, one-person job

Carries a Lifetime Marathon Warranty Includes a 2" spline shaft with a 1-1/4" pilot to aid in alignment.

This 2 jaw puller has a 1 ton capacity
The maximum reach of 2-1/8" with the maximum spread of 3-1/4"
Screw size 5/16" - 24 x 3-7/8"
Jaw thickness 9/64"These pullers are forged from quality steel, heat treated, and subjected to rigorous tests which exceed their rated capacity. These pullers enable you to remove and install parts for fast, effective repairs.

Manually operated, screw-powered device removes cylinder sleeves from most truck, bus and tractor engines
Handles wet and dry sleeves, you won't need to remove head studs
The puller enables one technician to handle sleeve pulling tasks
Not recommended for MACK engines

Provides safe and efficient handling of fuel tanks
Adjusts horizontally from 24" to 38" and vertically from 7" to 11" to service tanks up to 40 gallons
Universal adapter plate fits virtually all competitive transmission jacks on the market
Four support risers individually adjust to ensure perfect fit to any fuel tank design
Cross-link polyethylene foam pads protect tanks from damage Patent pending gearing mechanism ensures equal extension of lift arms to correctly balance load over jack. Use with OTC1728, OTC1793, OTC1793A, OTC1794 and OTC1794A. American made, carries lifetime Marathon Warranty.