[

Save 20% Off

Turn Signal Switch
Hover over the image to zoom in
Turn Signal Switch Turn Signal Switch
Share this:

Turn Signal Switch by BWD (part#S3264) / Switches

Part No. S3264 Warranty  
$68.99
Quantity  Add Turn Signal Switch To Cart

See if this part fits a specific vehicle.

Check Vehicle Fit

Brand: BWD
Advance Auto Parts Part#: 20474736
Suitable vehicles: Click to find if this product can be used with your vehicle:
  • Buick
    • Regal Custom
      • 1996
        • 1996 Buick Regal Custom (3.8L 231CI V6 FI VIN: K)
      • 1995
        • 1995 Buick Regal Custom (3.8L 231CI V6 FI VIN: L)
      • 1994
        • 1994 Buick Regal Custom (3.8L 231CI V6 FI VIN: L)
    • Regal Gran Sport
      • 1996
        • 1996 Buick Regal Gran Sport (3.8L 231CI V6 FI VIN: K)
      • 1994
        • 1994 Buick Regal Gran Sport (3.8L 231CI V6 FI VIN: L)
    • Roadmaster Estate
      • 1995
        • 1995 Buick Roadmaster Estate (5.7L 350CI V8 FI VIN: P)
    • Roadmaster Limited Wagon
      • 1996
        • 1996 Buick Roadmaster Limited Wagon (5.7L 350CI V8 FI VIN: P)
  • Chevrolet
    • Lumina
      • 1999
        • 1999 Chevrolet Lumina (3.1L 189CI V6 FI VIN: M)
        • 1999 Chevrolet Lumina (3.8L 231CI V6 FI VIN: K)
      • 1998
        • 1998 Chevrolet Lumina (3.1L 189CI V6 FI VIN: M)
      • 1997
        • 1997 Chevrolet Lumina (3.1L 189CI V6 FI VIN: M)
      • 1996
        • 1996 Chevrolet Lumina (3.1L 189CI V6 FI VIN: M)
      • 1995
        • 1995 Chevrolet Lumina (3.1L 189CI V6 FI VIN: M)
    • Lumina LS
      • 1997
        • 1997 Chevrolet Lumina LS (3.1L 189CI V6 FI VIN: M)
      • 1996
        • 1996 Chevrolet Lumina LS (3.1L 189CI V6 FI VIN: M)
      • 1995
        • 1995 Chevrolet Lumina LS (3.1L 189CI V6 FI VIN: M)
    • Lumina LTZ
      • 1998
        • 1998 Chevrolet Lumina LTZ (3.8L 231CI V6 FI VIN: K)
    • Monte Carlo
      • 1999
        • 1999 Chevrolet Monte Carlo (3.1L 189CI V6 FI VIN: M)
        • 1999 Chevrolet Monte Carlo (3.8L 231CI V6 FI VIN: K)
    • Monte Carlo LS
      • 1998
        • 1998 Chevrolet Monte Carlo LS (3.1L 189CI V6 FI VIN: M)
      • 1997
        • 1997 Chevrolet Monte Carlo LS (3.1L 189CI V6 FI VIN: M)
      • 1996
        • 1996 Chevrolet Monte Carlo LS (3.1L 189CI V6 FI VIN: M)
      • 1995
        • 1995 Chevrolet Monte Carlo LS (3.1L 189CI V6 FI VIN: M)
    • Monte Carlo Z34
      • 1998
        • 1998 Chevrolet Monte Carlo Z34 (3.8L 231CI V6 FI VIN: K)
      • 1996
        • 1996 Chevrolet Monte Carlo Z34 (3.4L 207CI V6 FI VIN: X)
      • 1995
        • 1995 Chevrolet Monte Carlo Z34 (3.4L 207CI V6 FI VIN: X)
  • Oldsmobile
    • Cutlass
      • 1997
        • 1997 Oldsmobile Cutlass (3.1L 189CI V6 FI VIN: M)
    • Cutlass Supreme
      • 1995
        • 1995 Oldsmobile Cutlass Supreme (3.1L 189CI V6 FI VIN: M)
      • 1994
        • 1994 Oldsmobile Cutlass Supreme (3.1L 189CI V6 FI VIN: M)
    • Cutlass Supreme S
      • 1994
        • 1994 Oldsmobile Cutlass Supreme S (3.1L 189CI V6 FI VIN: M)
    • Cutlass Supreme SL
      • 1997
        • 1997 Oldsmobile Cutlass Supreme SL (3.1L 189CI V6 FI VIN: M)
      • 1996
        • 1996 Oldsmobile Cutlass Supreme SL (3.1L 189CI V6 FI VIN: M)
      • 1995
        • 1995 Oldsmobile Cutlass Supreme SL (3.1L 189CI V6 FI VIN: M)
  • Pontiac
    • Grand Prix
      • 1996
        • 1996 Pontiac Grand Prix (3.1L 189CI V6 FI VIN: M)
    • Grand Prix SE
      • 1996
        • 1996 Pontiac Grand Prix SE (3.1L 189CI V6 FI VIN: M)
      • 1995
        • 1995 Pontiac Grand Prix SE (3.1L 189CI V6 FI VIN: M)
      • 1994
        • 1994 Pontiac Grand Prix SE (3.1L 189CI V6 FI VIN: M)


BWD switches are manufactured to meet or exceed OE performance.
Back To Top
Connector Gender:Male
Terminal Gender:Female

REVIEW SNAPSHOT®

by PowerReviews
BWDTurn Signal Switch
 
5.0

(based on 1 review)

Ratings Distribution

  • 5 Stars

     

    (1)

  • 4 Stars

     

    (0)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

Reviewed by 1 customer

Displaying review 1

Back to top

(0 of 1 customers found this review helpful)

 
5.0

it does its job

By tyrone536

from Boston, MA

Verified Buyer

Pros

  • Durable
  • Easy To Use
  • High-Performance
  • Lightweight
  • Versatile

Cons

    Best Uses

      Comments about BWD Turn Signal Switch:

      Good product it does it's job

      • Car & Truck:
      • Auto Enthusiast

      Comment on this review(earn points)

      Do you have questions about this product?(earn points for answers!)

       

      Ask a question, get answers from real customers and in-house experts. Or contact Customer Care by email or call 1-877-238-2623.

      3 Questions | 3 Answers
      Displaying questions 1-3
      • Q:

        I have a 98 Chevy Lumina . How do you get the plastic part around the steering column off?
        Asked on 2/26/2013 by Ken from GA

        1 answer

        • CUSTOMER CARE

          A:

          For replacing this BWD Turn Signal Switch - part# S3264, park the car with the steering wheel centered and the wheels straight ahead. Locate and remove the "Airbag" or "SRS" fuse in the passenger side fusebox. There is more than one fuse for the airbag system. Remove the Negative battery cable. Remove the trim panels underneath the driver's side of the dashboard. Locate the yellow "CPA" connector for the airbag underneath the dash to the right of the steering column and disconnect. Remove the blue (or green) pin from the center of the connector to allow for the tab to be depressed. Use the #30 TORX bit (or the corresponding Hex bit) to loosen the 2 bolts that secure the airbag to the steering wheel, located on the back of the wheel. The bolts will stay inside of the wheel. You will have to turn the wheel to the left to get to the left hand bolt. Lift the airbag module away from the steering wheel. Disconnect the horn wire and RSWC connector (if available.) The horn is disconnected by following the red wire down to the white plastic "cylinder" sticking up from the column. Press in on the cylinder and rotate it counter-clockwise, then it should pop out (it's spring loaded.). Set the airbag aside. Carry it with the driver's side facing away from you. Set it down on a workbench facing up. Point the wheels straight ahead once again. Remove the steering wheel nut. Install the steering wheel puller and remove the steering wheel. Remove the snap ring that retains the clockspring. Lift the clockspring off of the steering shaft and let it hang. Do not allow the yellow inner ring of the clockspring to rotate, otherwise you will have to reset it later. Draw a mark across the black and yellow rings for alignment purposes, and place a piece of tape across the rings to prevent them from turning. Remove the "wave" washer. Remove the plastic cover on the left side exposing the washer and dimmer switches. Pull the multifunction stalk straight out and disconnect the cruise control wiring from the washer switch. The part that's exposed now is the Lock Plate. It has a spring pressing up against the back of it, and it is held in place by a retaining clip. You will need to use the lock plate compressor tool to press down on the lock plate to take tension off the spring in order to remove the retaining clip. Use the lock plate compressor to depress the lock plate. The center of the tool threads on to the steering shaft, and the 2 "forks" press down on the lock plate. Use the 2 small screwdrivers to remove the lock plate retaining clip. Have patience with this step, 'cause it takes a while to work the clip loose. If you bend the clip, no worries, you can easily bend it back into shape. Remove the lock plate compressor. Lift off the lock plate, paying attention to where you have it aligned. You will need to align it in the same position when reassembling the column. Carefully remove the hazzard flasher knob from the top of the column. Remove the cancelling cam and spring. Remove the 2 screws that hold the dimmer switch to the signal switch. Remove the 3 screws retaining the signal switch in place. You will have to move the switch into the "right signal on" position to remove the final screw. Locate the bulkhead connector underneath the dash to the right of the steering column, loosen the large bolt in the center of the connector and pull the connector straight out it. The bolt has an 8mm head, BTW. The signal switch harness piggybacks to the ignition switch harness. With the Bulkhead connector unbolted and removed, remove the blue retaining tabs and slide the signal switch harness *backwards* to remove it. It only slides in one direction, BTW. You may need to wedge a tiny screwdriver in the center of the signal switch harness to get it to disengage from the bulkhead. If you have RSWC, disconnect the RSWC connector from the signal switch. Feed the wires up the column. You will have to first angle the harness so it will slip into the channel of the column. Pull on the signal switch to aid in feeding the wires up. Installation is the reverse of removal. When you get to point of reinstalling the clockspring, align the tab at the top centered with the notches near 12 O'Clock on the column. The springs are easily removed with a needle-nose pliers. Reassembly is the reverse of removal. For any further assistance, you may also call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

          Answered on 2/27/2013 by Vincent from AAP
      • Q:

        I have a 1998 Chevy Lumina and I was wondering if BDW S3264 will work on my car the turn signal switch i need controls: turn signals, wipers, washers, cruise control and high beams. Could you advise me cause my turn signals and cruise don't work and we have found that its in the switch. Thank You.
        Asked on 3/7/2012 by Stan from Naples, Fl.

        1 answer

        • CUSTOMER CARE

          A:

          This BWD Turn Signal Switch with Part No. S3264 is a multifunction switch which controls a variety of car elements, including headlights, turn signals and emergency flashers in your 1998 Chevrolet Lumina. If you notice any or all of these functions operating erratically, or not working at all, it is possible your multifunction switch has gone bad. The multifunction switch is located inside your steering wheel column and is fairly easy to access. Replacement will take you approximately 30 minutes.

          Answered on 3/9/2012 by John the Car-Doc from AAP
      • Q:

        Does this have the cruise, windshield washer on it as well
        Asked on 12/4/2011 by Bill from Omaha

        1 answer

        • CUSTOMER CARE

          A:

          No, it does not have the cruise, windshield washer on it.

          Answered on 12/6/2011 by John the Car-Doc from AAP
      Displaying questions 1-3

      Do you have a question about this product? 

      Create or view your online garage

      Check out the specials in our monthly flyer

       
       
      Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.